سلام
من بدنبال config روی موبایل بودم که به این آموزش برخوردم. اینجا میزارم تا دوستان هم استفاده کنند.
Configuring a Nokia E65 / E71 / N95 for 3CX Phone System
IMPORTANT This guide has been tested with the following firmware versions:
Nokia E65: 4.0633.74.00.
Nokia E71: 200.21.118
Nokia N95: 31.0.017
Be aware that different firmware revisions may have different web interface formats and functionality.
This guide is based on the configuration needed to setup your phone when you are in the range of a specific Wireless network. Tweaking of the access point for the connection will be required when moving to different WiFi zones.
Part 1: Configuring the Nokia device SIP client
- Ensure that you have created the extension that you wish to use with the phone in 3CX Phone System first. Take note of the Authentication ID and the Authentication Password that you have entered for the extension.
- Configure your Nokia mobile phone as per the manufacturer manual for web browsing. Once this is confirmed you may proceed to configure the Internet Telephone and SIP functions of the phone.
- From your Nokia go to "Tools" and then to "Settings". Click on "Connection" followed by "SIP settings".
- Choose the option to add a new default profile.
- In "Profile name" enter "3CX", move down to "Service profile" and choose "IETF" if you plan on using Private WLAN, or "Nokia 3GPP" if you plan to use a 3G Provider access point.
- Proceed to "Default access point" and choose your Private WLAN access point or 3G access point depending on your previous choice.
- In the "Public user name" field enter "<extension_number>@<pbx_ip_address>" from your 3CX server (Example: 100@192.168.1.1)
- In the "Use compression" field, choose "No", and under "Registration" choose "Always on". For the "Use security" select "No".
- Access the "Proxy server" node.
a. In the "Proxy server address" enter the IP Address of your 3CX PhoneSystem server (example: 192.168.1.1)
b. In the "Realm" field enter "3CXPhoneSystem"
c. In the "User name" field enter your extension number (example: 100)
d. In the "Password" field enter the Authentication Password for your extension
e. In the "Allow loose routing" field choose "Yes"
f. In the "Transport Type" field select "UDP"
g. In the "Port" field enter the 3CX PhoneSystem SIP Port (default is "5060") - Navigate back one step
- In the "Registrar Server" field enter the IP Address of your 3CX PhoneSystem server (example: 192.168.1.1)
- In the "Realm" field enter "3CXPhoneSystem"
- In the "User name" field enter your extension number (example: 100)
- In the "Password" field enter the Authentication Password for your extension
- In the "Transport Type" field select "UDP"
- In the "Port" field enter the 3CX PhoneSystem SIP Port (default is "5060")
- Go back to "Connection" and then to "Internet tel. settings"
- Create a new profile and call it "3CX" and under "SIP profiles" choose the "3CX" profile. In the Profile settings set the "Preferred call type" to "Internet call". This will ensure that the call attempts shall first look for an active SIP connection before using GSM / GPRS / UMTS.
Screenshot of outbound rule for Nokia devices
In view of the fact that a mobile user may be dialing contacts, if your 3CX Outbound rules make use of prefixes then specific outbound rules for the Nokia based extensions will need to be configured. Please refer to the 3CX manual for the creation of Outbound rules. Above is a screenshot of such a basic rule. You should have these rules topmost in the list.
Part 2: Nokia outside the PBX's LAN (Remote Extension)
In part 1, we used the default Nokia software to connect the Nokia Phone using SIP on the same LAN as 3CX PhoneSystem machine. This section explains the additional requirements when the Nokia Phone needs to connect to 3CX PhoneSystem as a remote extension.
- Make sure that your PC has the "Nokia PC Suite" software installed and up to date.
- Download the SIP_VOIP_Settings installer from SIP VoIP 2.x Settings
- From the Nokia PC Suite choose 'Install Application' and select the downloaded file.
- Once the installation is complete you will need to configure the VOIP settings from the phone.
a. Click on 'Menu' and navigate to Installations > SIP VOIP Settings.
b. Enter the 'NAT Firewall Settings' and enter the 'Domain Parameters settings'.
c. You will find your SIP domain already available. Enter this node.
a. In the 'STUN server name' enter 'stun.3cx.com'.
b. In the 'STUN Server Port' enter '3478'.
c. In the 'TCP Nat refresh' and 'UDP Nat Refresh' set the value to '2'.
Notes:
- Testing covered inbound and outbound call as well as Hold / Resume functionality.
- Blind Transfer is possible, but the phone does not include the functionality for Attended Transfer.
- To be able to edit the SIP Profile you will need to unregister the SIP Registration. This can be done from the Nokia Device > Menu > Communication > Internet Telephone > Disconnect SIP Profile option.