کمک در مورد over run روتر فوری !!!!!!!!!!!!!
با سلام خدمت اساتید محترم. من یه مشکل دارم هر شب روترم over run داره اونم زیاد . روتر as5300 هست .
کانفیگشم میزارم اینجا در ضمن من تازه واردم لطف کنید اگه اشکالی هست بگید.از ریز تا درشت. متشکرم.
[LEFT]Current configuration : 3809 bytes
!
version 12.3
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname 5300
!
boot-start-marker
boot-end-marker
!
!
username xxxx password xxxxxxx
spe 1/0 1/9
firmware location system:/ucode/mica_port_firmware
!
!
resource-pool disable
!
modem answer delay 1
modem country mica e1-default
aaa new-model
!
!
aaa authentication login dat local enable
aaa authentication login no_tacacs enable
aaa authentication login tac group tacacs+
aaa authentication enable default group tacacs+ enable
aaa authentication ppp default if-needed group tacacs+ local
aaa authentication ppp no_serial none
aaa authentication ppp tac group tacacs+
aaa authorization exec default group tacacs+ local
aaa authorization commands 1 default group tacacs+ local if-authenticated
aaa authorization commands 15 default group tacacs+ local if-authenticated
aaa authorization network default group tacacs+ local
aaa accounting nested
aaa accounting update newinfo
aaa accounting exec default start-stop group tacacs+
aaa accounting network default start-stop group tacacs+
aaa session-id common
ip subnet-zero
ip name-server 217.218.127.106
!
!
isdn voice-call-failure 0
!
!
controller E1 0
framing NO-CRC4
clock source line primary
ds0-group 0 timeslots 1-15,17-31 type r2-digital
cas-custom 0
!
controller E1 1
framing NO-CRC4
clock source line secondary 1
line-termination 75-ohm
ds0-group 1 timeslots 1-15,17-31 type r2-digital
cas-custom 1
!
controller E1 2
framing NO-CRC4
clock source line secondary 2
ds0-group 2 timeslots 1-15,17-31 type r2-digital
cas-custom 2
!
controller E1 3
framing NO-CRC4
clock source line secondary 3
ds0-group 3 timeslots 1-15,17-31 type r2-digital
cas-custom 3
!
controller E1 4
clock source line secondary 4
!
controller E1 5
clock source line secondary 5
!
controller E1 6
clock source line secondary 6
!
controller E1 7
clock source line secondary 7
!
!
interface Ethernet0
ip address x.x.x.x x.x.x.x
load-interval 30
!
interface Serial0
ip unnumbered FastEthernet0
encapsulation ppp
no fair-queue
no cdp enable
!
interface Serial1
no ip address
shutdown
clockrate 2015232
no fair-queue
!
interface Serial2
no ip address
shutdown
clockrate 2015232
no fair-queue
!
interface Serial3
no ip address
shutdown
clockrate 2015232
no fair-queue
!
interface FastEthernet0
ip address x.x.x.x x.x.x.x secondary
ip address x.x.x.x x.x.x.x secondary
ip address x.x.x.x x.x.x.x
no ip unreachables
no ip mroute-cache
duplex auto
speed auto
no keepalive
no cdp enable
!
interface Group-Async1
ip unnumbered FastEthernet0
encapsulation ppp
ip tcp header-compression
ip policy route-map cache
load-interval 30
async mode interactive
peer default ip address pool dial
ppp authentication pap
group-range 1 120
!
ip local pool dial x.x.x.x x.x.x.x
ip nat inside source list 7 interface FastEthernet0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0
no ip http server
!
!
access-list 7 permit x.x.x.x 0.0.0.255
access-list 50 permit x.x.x.x
access-list 50 permit x.x.x.x
access-list 50 permit x.x.x.x
access-list 50 deny any
access-list 110 permit tcp any any eq www
access-list 110 permit tcp any any
!
route-map cache permit 10
match ip address 110
set ip next-hop x.x.x.x
!
tacacs-server host x.x.x.x
tacacs-server directed-request
snmp-server community public RW 20
snmp-server enable traps tty
!
!
!
!
!
line con 0
line 1 120
modem Dialin
modem autoconfigure type mica
autocommand ppp
transport preferred none
transport input all
transport output none
autoselect during-login
autoselect ppp
line aux 0
line vty 0 4
password xxxxxxxx
!
end[/LEFT]
