نمایش نتایج: از شماره 1 تا 5 از مجموع 5
سپاس ها 2سپاس
  • 1 توسط mojtaba461
  • 1 توسط j_p

موضوع: چگونگی استفاده از ویندوز به عنوان روتر

  
  1. #1
    alm
    alm آنلاین نیست.
    نام حقيقي: مهدی

    خواننده
    تاریخ عضویت
    May 2014
    محل سکونت
    تهران
    نوشته
    14
    سپاسگزاری شده
    0
    سپاسگزاری کرده
    8

  2. #2
    نام حقيقي: محمد رسول راستی

    مدیر عمومی شناسه تصویری M-r-r
    تاریخ عضویت
    Feb 2004
    محل سکونت
    تهران
    نوشته
    9,486
    سپاسگزاری شده
    4309
    سپاسگزاری کرده
    2706
    سوالتون واضح نیست، با جزئیات بیشتر موضوع رو مطرح کنید.


    Mohammad Rasoul Rasti
    There's no place like 127.0.0.1
    m.rasti [@] outlook.com

  3. #3
    alm
    alm آنلاین نیست.
    نام حقيقي: مهدی

    خواننده
    تاریخ عضویت
    May 2014
    محل سکونت
    تهران
    نوشته
    14
    سپاسگزاری شده
    0
    سپاسگزاری کرده
    8
    ممنون از سرعت پاسخگویی

    یک کامپیوتر دارم با دو تا کارت شبکه و آدرس IP ها متفاوت.
    میخام تمامی ترافیک کارتشبک اول را با تغییر آدرس IP به کارت شبکه دوم ارسال کنم. در واقع با نصب ویندوز با نسخه پیشنهای شما
    میخام از این کامپیوتر در شبکه ام به عنوان روتر استفاده کنم. الان دیگه واضحه؟



  4. #4
    نام حقيقي: مجتبی شمس نجاتی

    عضو عادی شناسه تصویری mojtaba461
    تاریخ عضویت
    Aug 2012
    محل سکونت
    لاهیجان
    نوشته
    2,368
    سپاسگزاری شده
    2269
    سپاسگزاری کرده
    706
    نوشته های وبلاگ
    11
    ویندوز سرور نصب کنید و از قابلیتهای routing and remote service میتونید استفاده کنید. بعنوان nat server


    alm سپاسگزاری کرده است.

  5. #5
    j_p
    j_p آنلاین نیست.
    نام حقيقي: جواد پورفرهاد

    عضو عادی شناسه تصویری j_p
    تاریخ عضویت
    May 2013
    محل سکونت
    آبادان
    نوشته
    243
    سپاسگزاری شده
    139
    سپاسگزاری کرده
    86
    route [-f] [-p] [Command [Destination] [mask Netmask] [Gateway] [metric Metric]] [if Interface]]


    Parameters

    -f: Clears the routing table of all entries that are not host routes (routes with a netmask of 255.255.255.255), the loopback network route (routes with a destination of 127.0.0.0 and a netmask of 255.0.0.0), or a multicast route (routes with a destination of 224.0.0.0 and a netmask of 240.0.0.0). If this is used in conjunction with one of the commands (such as add, change, or delete), the table is cleared prior to running the command.
    -p: When used with the add command, the specified route is added to the registry and is used to initialize the IP routing table whenever the TCP/IP protocol is started. By default, added routes are not preserved when the TCP/IP protocol is started. When used with the print command, the list of persistent routes is displayed. This parameter is ignored for all other commands. Persistent routes are stored in the registry location HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\Tcpip\Parameters\PersistentRoutes.
    Command: Specifies the command you want to run. The following table lists valid commands.


    add Adds a route.
    change Modifies an existing route.
    delete Deletes a route or routes.
    print Prints a route or routes.



    alm سپاسگزاری کرده است.

کلمات کلیدی در جستجوها:

هیچ کلمه ای ثبت نشده است.

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •