چطور میشه از ویندوز و یا یکی از سرویس های اون به عنوان روتر استفاده کرد؟
Printable View
چطور میشه از ویندوز و یا یکی از سرویس های اون به عنوان روتر استفاده کرد؟
سوالتون واضح نیست، با جزئیات بیشتر موضوع رو مطرح کنید.
ممنون از سرعت پاسخگویی
یک کامپیوتر دارم با دو تا کارت شبکه و آدرس IP ها متفاوت.
میخام تمامی ترافیک کارتشبک اول را با تغییر آدرس IP به کارت شبکه دوم ارسال کنم. در واقع با نصب ویندوز با نسخه پیشنهای شما
میخام از این کامپیوتر در شبکه ام به عنوان روتر استفاده کنم. الان دیگه واضحه؟
ویندوز سرور نصب کنید و از قابلیتهای routing and remote service میتونید استفاده کنید. بعنوان nat server
[B]route[/B] [[B]-f[/B]] [[B]-p[/B]] [[I]Command[/I] [[I]Destination[/I]] [[B]mask[/B] [I]Netmask[/I]] [[I]Gateway[/I]] [[B]metric[/B] [I]Metric[/I]]] [[B]if[/B] [I]Interface[/I]]]
[B]Parameters[/B]
[B]-f[/B][B]: [/B]Clears the routing table of all entries that are not host routes (routes with a netmask of 255.255.255.255), the loopback network route (routes with a destination of 127.0.0.0 and a netmask of 255.0.0.0), or a multicast route (routes with a destination of 224.0.0.0 and a netmask of 240.0.0.0). If this is used in conjunction with one of the commands (such as [B]add[/B], [B]change[/B], or [B]delete[/B]), the table is cleared prior to running the command.
[B]-p[/B][B]: [/B]When used with the [B]add[/B] command, the specified route is added to the registry and is used to initialize the IP routing table whenever the TCP/IP protocol is started. By default, added routes are not preserved when the TCP/IP protocol is started. When used with the [B]print[/B] command, the list of persistent routes is displayed. This parameter is ignored for all other commands. Persistent routes are stored in the registry location [B]HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services[/B][B]\Tcpip\Parameters\PersistentRoutes[/B].
[B][I]Command[/I][/B][B]: [/B]Specifies the command you want to run. The following table lists valid commands.
[TABLE="class: dataTable"]
[TR="class: record"]
[TD][B]add[/B][/TD]
[TD]Adds a route.[/TD]
[/TR]
[TR="class: evenRecord"]
[TD][B]change[/B][/TD]
[TD]Modifies an existing route.[/TD]
[/TR]
[TR="class: record"]
[TD][B]delete[/B][/TD]
[TD]Deletes a route or routes.[/TD]
[/TR]
[TR="class: evenRecord"]
[TD][B]print[/B][/TD]
[TD]Prints a route or routes.[/TD]
[/TR]
[/TABLE]