نمایش نتایج: از شماره 1 تا 9 از مجموع 9
سپاس ها 13سپاس
  • 9 توسط alisc
  • 2 توسط alisc
  • 2 توسط mohsenhvac

موضوع: کانفینگ کردن دو تا رادیو sxt میکروتیک

  
  1. #1
    نام حقيقي: javad

    تازه وارد
    تاریخ عضویت
    Sep 2014
    محل سکونت
    sabzevar
    نوشته
    3
    سپاسگزاری شده
    0
    سپاسگزاری کرده
    0

    کانفینگ کردن دو تا رادیو sxt میکروتیک

    سلام به همه دوستان
    شغل من نصب وراه اندازی دوربین مدازبسته وتا حدودی شبکه های کامپیوتری
    در حین کار نیاز شده که دونقطه رو با آنتن میکروتیک sxt شبکه کنیم
    اگر کسی اطلاعات داره .تنظمیات کانفینگ این رادیو ها رو میخواستم
    ممنون میشم کمک کنید



    موضوعات مشابه:

  2. #2
    نام حقيقي: علی شفائی

    عضو عادی شناسه تصویری alisc
    تاریخ عضویت
    Sep 2010
    محل سکونت
    شهریار
    نوشته
    1,897
    سپاسگزاری شده
    1730
    سپاسگزاری کرده
    2052
    با سلام
    ابتدا ورودتون رو به انجمن خوش آمد میگم

    خدمت شما :
    Bridging Networks with SXT

    Two RouterBOARD SXT devices can be used to establish transparent wireless point-to-point network link. There are multiple options how to do that. This guide shows the most simple and easiest way how to do that by using bridge wireless mode on one side and station-bridge wireless mode on the other side.
    RouterBOARD SXT devices has only Level 3 RouterOS license, but even with that it is possible to make wireless connection between two SXT devices.

    Make connection to the RouterBOARD SXT

    There are multiple ways how to connect to the RouterBOARD (winbox, webfig, telnet, ssh, ...), but this guide will show how to configure the device using Winbox utility. Winbox utility can be downloaded from the MikroTik webpage ( Winbox) or from the RouterBOARDs webpage. The SXT device by default has IP address 192.168.88.1 configured as a default IP address on the ethernet interface. In order to connect to the SXT device make sure your computers IP address range is form the same network address space. Connect the ethernet cable from the PC to the SXT device and power it on. Open the Winbox utility and in the "Connect To" field write the IP address of the SXT device. If it can't connect click on the "..." button to search for a RouterOS based devices. In that discovery windows select the SXT device IP or MAC which you found and click Connect.

    Configure the first SXT device to the wireless bridge mode

    SXT device has build in default wireless configuration already, so only few changes are needed to be done. Open Wireless menu and select the wireless interface. Change the Mode setting to "bridge" and specify the "frequency" on which the wireless radio will be operating. If you don't see your countries allowed frequencies, then click in the "Advanced Mode" and chose your country from the "country" dropbox field and then chose the frequency. It is recommended to use the frequency that is in the bold in the wireless frequency drop down field. It is suggested to click on a "Apply" after each setting change as if you configure some setting incorrectly every setting will be reverted to the previous state (not recommended when the link is already active and running).

    Disable the NAT (masquerade) rule in the IP Firewall NAT menu as it is not needed when the transparent wireless setupo is used. Disable the Firewall rule the IP Firewall Filter Input chain.

    Disable the DHCP server and DHCP client as they are not needed in the transparent wireless setup. Go to the IP DHCP Server menu and disable the server. Go to the IP DHCP Client menu and disable the client.

    Create a Bridge interface and add add ethernet and wireless interface to the bridge ports. Open Bridge menu and click on "+" and press OK. Open Bridge Ports menu and add 2 entries, one with ethernet interface added to the bridge and second with wireless interfaces added to the bridge.

    It is advised to do so as the default IP address that the SXT device usually is used only for initial configuration as you may confuse the SXT device with the other one if they both will be online in the same network. Add an IP address to the bridge interface to communicate to the router after the SXT device will be deployed in the network. IP address can be added from the IP Address menu.

    The basic configuration for the Bridge mode device is done.
    Configure the second SXT device to the wireless station-bridge mode

    Connect to the second SXT device the same way as it is described in first step. Configuration of the second SXT device is similar to the first one.
    Open Wireless menu and select the wireless interface. Change the Mode setting to "station-bridge". Make sure that you use the same country as the first SXT device. In order to change the country setting you need to click on the "Advanced Mode" button and then you will see the country field.
    [image with station-bridge and county]
    Disable the NAT (masquerade) rule in the IP Firewall NAT menu as it is not needed when the transparent wireless setupo is used. Disable the Firewall rule the IP Firewall Filter Input chain.
    [image on NAT disable and filter disable]
    Disable the DHCP server and DHCP client as they are not needed in the transparent wireless setup. Go to the IP DHCP Server menu and disable the server. Go to the IP DHCP Client menu and disable the client.
    [image with both menus]
    Create a Bridge interface and add add ethernet and wireless interface to the bridge ports. Open Bridge menu and click on "+" and press OK. Open Bridge Ports menu and add 2 entries, one with ethernet interface added to the bridge and second with wireless interfaces added to the bridge.
    [image with bridge port add dialog for both interfaces]
    It is advised to do so as the default IP address that the SXT device usually is used only for initial configuration as you may confuse the SXT device with the other one if they both will be online in the same network. Add an IP address to the bridge interface to communicate to the router after the SXT device will be deployed in the network. IP address can be added from the IP Address menu.
    [image with IP address adding]
    The basic configuration for the Station-bridge device is done.
    Finetuning the RouterOS configuration to get the max speed

    After both devices are configured you should be able to see from the station-bridge device that the wireless connection is established. It also means that the transparent setup should be working fine and you should be able to communicate between both networks that are connected to the SXT ethernet sides.
    [image with wireless monitor on station-bridge]




    mehrzadmo، mohsenhvac، amir-yazde و 6 نفر دیگر سپاسگزاری کرده‌اند.

  3. #3
    نام حقيقي: javad

    تازه وارد
    تاریخ عضویت
    Sep 2014
    محل سکونت
    sabzevar
    نوشته
    3
    سپاسگزاری شده
    0
    سپاسگزاری کرده
    0
    سلام علی آقا
    ممنون از کمکتون
    خیلی کمک کرد
    یه سوال دیگه هم دارم آیا میشه 3تا sxt رو باهم کانفینگ کرد منظورم اینه که دوتاشون(یکی station و دومی bridg) با فاصله 500 مترین یکی دیگه در فاصله 50 متری از bridg من خواستم این کار بکنم اما باهم قاطی کردن هرکودوم از stationها زودتر کانفینگ میشود دومی دیگه وصل نمیشد اگه این حالت امکان پذیره راهنمایی کنید


    ویرایش توسط shafaghits : 2014-09-07 در ساعت 10:21 PM

  4. #4
    نام حقيقي: علی شفائی

    عضو عادی شناسه تصویری alisc
    تاریخ عضویت
    Sep 2010
    محل سکونت
    شهریار
    نوشته
    1,897
    سپاسگزاری شده
    1730
    سپاسگزاری کرده
    2052
    نقل قول نوشته اصلی توسط shafaghits نمایش پست ها
    سلام علی آقا
    ممنون از کمکتون
    خیلی کمک کرد
    یه سوال دیگه هم دارم آیا میشه 3تا sxt رو باهم کانفینگ کرد منظورم اینه که دوتاشون(یکی station و دومی bridg) با فاصله 500 مترین یکی دیگه در فاصله 50 متری از bridg من خواستم این کار بکنم اما باهم قاطی کردن هرکودوم از stationها زودتر کانفینگ میشود دومی دیگه وصل نمیشد اگه این حالت امکان پذیره راهنمایی کنید
    لایسنس یکی را آپدیت کنید تا قابلیت AP اضافه شود
    سپس یکی را AP بزارید - ۲ تای دیگر را استیشن


    nadali و nahvi18 سپاسگزاری کرده‌اند.

  5. #5
    نام حقيقي: amir

    تازه وارد
    تاریخ عضویت
    Oct 2010
    محل سکونت
    kashan
    نوشته
    5
    سپاسگزاری شده
    3
    سپاسگزاری کرده
    14
    ممنون میشم اگه لطف کنید بگید این لایسنس و آپیدت کردنش یعنی چی و چجوریه
    من تاحالا از نزدیک کار نکردم ولی علاقه دارم بدونم چجوری این اتفاق می افته؟
    ممنون



  6. #6
    نام حقيقي: محسن نیک قلب رودسری

    عضو عادی شناسه تصویری mohsenhvac
    تاریخ عضویت
    Sep 2008
    محل سکونت
    گیلان- رودسر
    نوشته
    2,203
    سپاسگزاری شده
    1944
    سپاسگزاری کرده
    1310
    Manual:License - MikroTik Wiki
    کد:
    Level number 0 (Trial mode) 1 (Free Demo) 3 (WISP CPE) 4 (WISP) 5 (WISP) 6 (Controller)
    Price no key registration required volume only $45 $95 $250
    Initial Config Support - - - 15 days 30 days 30 days
    Wireless AP 24h trial - - yes yes yes
    Wireless Client and Bridge 24h trial - yes yes yes yes
    RIP, OSPF, BGP protocols 24h trial - yes(*) yes yes yes
    EoIP tunnels 24h trial 1 unlimited unlimited unlimited unlimited
    PPPoE tunnels 24h trial 1 200 200 500 unlimited
    PPTP tunnels 24h trial 1 200 200 500 unlimited
    L2TP tunnels 24h trial 1 200 200 500 unlimited
    OVPN tunnels 24h trial 1 200 200 unlimited unlimited
    VLAN interfaces 24h trial 1 unlimited unlimited unlimited unlimited
    HotSpot active users 24h trial 1 1 200 500 unlimited
    RADIUS client 24h trial - yes yes yes yes
    Queues 24h trial 1 unlimited unlimited unlimited unlimited
    Web proxy 24h trial - yes yes yes yes
    User manager active sessions 24h trial 1 10 20 50 Unlimited
    Number of KVM guests none 1 Unlimited Unlimited Unlimited Unlimited
    - - - ادامه - - -

    همونطور که در جدول بالا میبینی سیستم عامل میکروتیک دارای سطحهای مختلفی هست و هرکدوم محدودیتهای خاص خودشون رو دارن.
    لول یک و دو که خب مشخصه عملا کاربردی ندارن. سطح سه جهت تجهیزات cpe هست یعنی دستگاههایی که لولشون 3 هست قابلیت تبدیل شدن به ap رو ندارن و تنها به صورت ptp یا استیشن قابل استفاده هستن. البته محدودیتهایی از نظر تعداد تونلها و ... دارن که در برابر مورد قبلی زیاد به چشم نمیاد.
    از لول چهار به بعد هم که مشخصه قابلیت ap شدن دارن و سایر قابلیتها هم کم کم افزایش پیدا می کنه تا اینکه به حالت نا محدود می رسه


    mehrzadmo و amir-yazde سپاسگزاری کرده‌اند.

  7. #7
    نام حقيقي: amir

    تازه وارد
    تاریخ عضویت
    Oct 2010
    محل سکونت
    kashan
    نوشته
    5
    سپاسگزاری شده
    3
    سپاسگزاری کرده
    14
    آپیدت کردنش چه شکلیه؟



  8. #8
    نام حقيقي: محسن نیک قلب رودسری

    عضو عادی شناسه تصویری mohsenhvac
    تاریخ عضویت
    Sep 2008
    محل سکونت
    گیلان- رودسر
    نوشته
    2,203
    سپاسگزاری شده
    1944
    سپاسگزاری کرده
    1310
    گاهی اوقات ممکن است لایسنسی که بروی روتر بورد سخت افزاری یا نرم افزاری هست به گونه ایی باشد که استفاده از تمامی مزیت ها و امکانات را از شما گرفته باشد ُ*به همین دلیل لازم است ارتقا لایسنس داشته باشید تا بتوانید از ویژگی های متعدد برخوردار شوید .

    ارتقا لایسنس یه چندین صورت میتواند صورت گیرد :

    وارد کردن رشته ( استرینگ کامل )*لایسنس از طریق اف تی پی و یا کنسول
    وارد کردن لایسنس از طریق رجیستر فایل (*ایمپورت کردن )
    دانلود شدن لایسنس مورد نظر از طریق اینترنت توسط خود میکروتیک

    در هنگام وارد کردن لایسنس از شما شماره نرم افزاری پرسیده میشود که این لایسنس بروی چه نسخه ایی (*ثبت )*قرار است توسط میکروتیک ثبت گردد .
    در نهایت لازم است روتربورد را ریستارت نمایید .

    در مثال زیر من دو عدد روتر بورد RB411AH را که با لایسنس ۳ بود را به ۴ ارتقا دادم .

    به این دلیل که لایسنس ۳ نمیتواند در بخش وایرلس در حالت Access Point ( AP-Bridge ) قرار گیرد و همچنین تعداد استفاده از سرویس هات اسپات ۱ میباشد .

    لازمه بگم که در پروفایل خود در میکروتیک لایسنس داشتم .

    برای روتر برد اول : وارد پروفایل خودم در سایت میکروتیک شدم ُ بخش ساخت لایسنس (*یا صدور لایسنس ) ُ*شماره نرم افزاری میکروتیک را دادم و لایسنس مورد نظر به آن انتساب داده شد و سپس رشته لایسنس را در میکروتیک وارد کردم .

    اطلاعات تراکنش لایسنس که ایمیل شده به من و شامل رشته و فایل رجیستری لایسنس هست :

    On: 2011-07-09 14:52:42
    Customer account: Reza Moghadam
    Computer located at IP: 95.82.116.30
    Paid by: Free of charge
    License: WISP AP (Level 4)

    Software ID: XXDL-YXXP
    The software Key is:
    -----BEGIN MIKROTIK SOFTWARE KEY------------
    ۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۰۱۰۱۰۱۰۱ ۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰
    zORZl0fTY4xKrA۱۲۱۲۱۲۱۲۱۲۱۲۱۲۱۲۱۲ ۱۲۱۲۱۲۱۲۱۲۱۲۱۲۱
    -----END MIKROTIK SOFTWARE KEY--------------


    در میکروتیک دوم ُ*نام کاربری پروفایل و رمز عبور را وارد بخش System > License نمودم و بطور اتوماتیک لایسنس مورد نظر را برداشت کرد .

    اطلاعات تراکنس دوم :

    On: 2011-07-09 14:55:17
    Customer account: Reza Moghadam
    Computer located at IP: 95.82.116.30
    Paid by: Free of charge
    License: WISP AP (Level 4)

    Software ID: PZM5-YXXK
    The software Key is:
    -----BEGIN MIKROTIK SOFTWARE KEY------------
    ۱۲۱۲۱۲۱۲۱۲۱۲۱۲۱۲۱۰۱۰۱۰۱۲۱ ۰۱۲۱۰۱۱۲۱۱۰۰۱۱۰۱۰۰۱۰۱
    ۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰ ۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱۰۱
    -----END MIKROTIK SOFTWARE KEY--------------



    To view/print Invoice for your license, please log into your mikrotik.com
    account, and click on `all keys`. There you will be able to download
    Invoices in PDF format.

    Entering the key from Console/FTP :

    * import the attached file with the command '/system license import'
    (you should upload this file to the router's FTP server)

    Entering the key with Console/Telnet:

    * use copy/paste to enter the key into a Telnet window (no matter which
    submenu).
    Be sure to copy the whole key, including the lines
    "--BEGIN MIKROTIK SOFTWARE KEY--" and "--END MIKROTIK SOFTWARE KEY--"

    Entering the key from Winbox:

    * use 'system -> license' menu in Winbox to Paste or Import the key

    نکته : زمانی که قصد دارید ارتقا لایسنس را از طریق رشته موجود انجام دهید ُ*لازم است که حتما زشته --BEGIN MIKROTIK SOFTWARE KEY-- و همچنین رشته --END MIKROTIK SOFTWARE KEY-- در ابتدا و انتهای رشته لایسنس وارد شود .

    نویسنده : رضا مقدم از انجمن سیسکو به پارسی



  9. #9
    نام حقيقي: علی رحمتی

    تازه وارد
    تاریخ عضویت
    Sep 2014
    محل سکونت
    یزد
    نوشته
    11
    سپاسگزاری شده
    1
    سپاسگزاری کرده
    4
    سلام
    استاد عزیز منم همین مشکل رو دارم . الان میخوام یه Sixtant رو بزارم رو مد AP Bridge اما میگه لایسنسش کافی نیست ( Level 3 ) . الان باید چی کار کنم ؟ تو سایتش رجیستر کنم بهم لایسنس میده ؟ Software ID منم اینه : D04Q-RY13



کلمات کلیدی در جستجوها:

نحوه ی نصب و پیکربندی وایرلس میکروتیک SXT

کانفینگ کردن رادیو

persian mikrotik ir webfig

کانفیگ میکروتیک sxt

نحوه اتصال به رادیو sxt

کانفیگ رادیو میکروتیک

تنظیم فرکانس شبکه sxt

آموزش کانفیگ آنتن میکروتیک

کانفیگ انتن های میکروتیکsxt lite5

نحوه کانفیگ رادیو میکروتیک

تنظیمات میکروتیکp2p

اموزش پوینت کردن رادیو میکروتیک

کتاب در مورد نصب sxt

اموزش طریقه کانفیگ انتن میکروتیک به صورت pdf

کانفیگ میکروتیک sxt lite5

نحوه کانفیک انتن میکروتیک در لایحه سه

پیکربندی آنتن میکروتیک

آموزش تنظیمات stxکانفیگ رادیو sxtاتصال به رادیو sxt lite5نحوه کانفیگ رادیو sxt نصب میکروتیک ،مجوز میخواد ؟sxt lite 2کانفیک کردن آنتن SXT وایرلست sxt lite5 تنظیماتآموزش میکروتیک پوینت تو پوینت pdf

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •