نمایش نتایج: از شماره 1 تا 15 از مجموع 15
سپاس ها 27سپاس
  • 2 توسط exxtreme
  • 7 توسط eng_amir68
  • 1 توسط exxtreme
  • 2 توسط eng_amir68
  • 1 توسط exxtreme
  • 2 توسط eng_amir68
  • 1 توسط exxtreme
  • 4 توسط mohamad-23
  • 1 توسط mahdi2008
  • 1 توسط eng_amir68
  • 4 توسط eng_amir68
  • 1 توسط mjzaret

موضوع: نصب ویندوز از طریق شبکه

  
  1. #1
    نام حقيقي: رضا

    خواننده
    تاریخ عضویت
    Jan 2012
    محل سکونت
    تهران
    نوشته
    574
    سپاسگزاری شده
    141
    سپاسگزاری کرده
    511

    نصب ویندوز از طریق شبکه

    دوستان یک شبکه با 50 تا کلاینت و یه سرور با ویندوز سرور 2003 است.
    میخوام بدونم سریع ترین راه برای نصب ویندوز xp و تمام برنامهاش روی کلاینتها چیه؟
    یعنی میشه روی یکی xp و برنامه هارو نصب کرد بعد با ایمیج روی همشون بطور همزمان نصب کرد یا باید پشت هر کدوم نشست؟
    در ضمن روی کلاینتها هیچ ویندوزی نصب نیست و سخت افزار همشون هم مثل هم است.



    موضوعات مشابه:
    arash3400 و shie سپاسگزاری کرده‌اند.

  2. #2
    نام حقيقي: amir

    عضو عادی شناسه تصویری eng_amir68
    تاریخ عضویت
    Jul 2010
    محل سکونت
    tehran
    نوشته
    295
    سپاسگزاری شده
    171
    سپاسگزاری کرده
    93
    اره چرا نمیشه.هم میتونی ایمیج بگیری و هم میتونی با nlite ویندوزتو سفارشی کنی بعد بری روی سرور remote installation services رو نصب کنی و ادامه ماجرا.
    اینم بگم که توی سرور2008 RIS به windows deployments services یا WDS تغییر پیدا کرده.


    mehrzadmo، mahdi2008، arash3400 و 4 نفر دیگر سپاسگزاری کرده‌اند.

  3. #3
    نام حقيقي: رضا

    خواننده
    تاریخ عضویت
    Jan 2012
    محل سکونت
    تهران
    نوشته
    574
    سپاسگزاری شده
    141
    سپاسگزاری کرده
    511
    کارش زیاده؟یا راحته؟من ویندوز نصب کنم با برنامه ها و بعد با norton ghost15 ایمیج بگیرم.بعد چیکار کنم؟یه توضیح بده دمت گرم.
    این ریموت تو 2003 کجاست؟


    arash3400 سپاسگزاری کرده است.

  4. #4
    نام حقيقي: amir

    عضو عادی شناسه تصویری eng_amir68
    تاریخ عضویت
    Jul 2010
    محل سکونت
    tehran
    نوشته
    295
    سپاسگزاری شده
    171
    سپاسگزاری کرده
    93
    setup a windows 2003 RIS server in 3 easy steps - www.windows-noob.com
    This step-by-step article describes how to use Remote Installation Service (RIS) to install Windows Server 2003 on remote computers.

    You can use RIS to remotely set up new Microsoft Windows Server 2003-based computers by using a RIS network shared folder as the source of the Windows Server 2003 files. You can install operating systems on remote boot-enabled client computers. Client computers are connected to the network, and are then started by using a Pre-Boot eXecution Environment (PXE)-capable network adapter or remote boot disk. The client then logs on with a valid user account.

    Back to the top
    RIS Hardware Requirements

    The following is the minimum hardware that is required for the RIS server:
    • The server must meet the minimum hardware requirements for the version of Windows Server 2003 that is installed.
    • A four gigabyte (GB) drive that is dedicated to the RIS directory tree on the RIS server.
    • A 10 or 100 megabit per second (Mbps) network adapter that supports TCP/IP. 100 Mbps is preferred.

      NOTE: Dedicate a whole hard disk or partition specifically to the RIS directory tree. SCSI-based disk controllers and disks are preferred.

      The drive on the server on which you will install RIS must be formatted with the NTFS file system. RIS requires a lot of disk space, and you cannot install it on the same drive or partition on which Windows Server 2003 is installed. Make sure that the chosen drive contains enough free disk space for at least one full set of the installation files for the operating system you plan to remotely install.
    Back to the top
    Client Hardware Requirements

    The following list describes the minimum hardware that is required for RIS client computers:
    • Meet the minimum operating system hardware requirements.
    • PXE DHCP-based boot ROM version 1.00 or later network adapter, or a network adaptor that is supported by the RIS boot disk.

      NOTE: Always contact the manufacturer of your network adapter to obtain the latest version of the PXE DHCP-based boot ROM.
    Back to the top
    Software Requirements

    Several network services must be active and available for RIS. You can install the following services either on the RIS server or on other servers that are available on the network:
    • Domain Name System (DNS Service)
    • Dynamic Host Configuration Protocol (DHCP)
    • Active Directory "Directory" service
    Back to the top
    Prerequisites for Client Installations

    Make sure that the client computer's network adapter has been set as the primary boot device in the computer BIOS. If the network adapter is configured as the primary boot device, the client requests a network service boot from the RIS server on the network when the client starts. After the client contacts the RIS, the client is prompted to press the F12 key to download the Client Installation Wizard. Do not press F12 unless you need a new operating system installation or access to maintenance and troubleshooting tools.

    After the client operating system has been installed by using RIS, you can ignore the prompt to press F12 during future client computer startups. You can also reset the client BIOS so that the primary boot device is the floppy disk drive, the hard disk, or the CD-ROM drive.

    To use the remote boot disk to start the installation, insert the boot disk into the floppy disk drive, and then start the client computer. The floppy disk drive must be set as the primary boot device in the client BIOS. After the computer starts from the disk, you are prompted to press F12 to start the network service boot process. You must remove the boot disk after you press F12 and before the text-mode portion of the operating system installation completes.

    NOTE: You may have to press F12 on some Compaq computers during startup. In this case, you must press F12 on the Compaq startup screen, and then press F12 again when you are prompted by the RIS server.

    Back to the top
    Install Windows Server 2003 RIS

    1. Click Start, point to Control Panel, and then click Add or Remove Programs.
    2. Click Add/Remove Windows Components.
    3. Click to select the Remote Installation Services check box, and then click Next.

      NOTE: If you are prompted for the Windows Server 2003 installation files, put the Windows Server 2003 CD-ROM in the CD-ROM drive, and then click OK. After you do so, you may receive a message with options for upgrading the operating system. Click No.
    4. Click Finish, and then click Yes to restart your computer.
    Back to the top
    Set Up RIS

    1. Log on as a user with administrative privileges.
    2. Click Start, click Run, type risetup.exe, and then click OK to start the RIS Setup Wizard.
    3. When the "Welcome" screen appears, click Next.
    4. Type the drive letter and folder in which the RIS files are stored, and then click Next. For example, you might type E:\RemoteInstall, and then click Next.
    5. After the RIS Setup Wizard copies the files, you are be prompted to enable or disable the RIS service, and the options are:
      • Respond to client computers requesting service. If you select this option, RIS is enabled, and it will respond to client computers that are requesting service.
      • Do not respond to unknown client computers. If you select this option, RIS only responds to known client computers.
    6. Click Respond to client computers requesting service, and then click Next.
    7. You are then prompted for the location of the client operating system installation files. Put the client operating system CD-ROM in the server CD-ROM drive, and then click Next.

      NOTE: Microsoft only supports the use of Microsoft media when creating a client operating system image. The use of non-Microsoft media is not supported.
    8. Type the folder name for the client operating system installation files on the RIS server, and then click Next.
    9. Type a friendly description for the operating system image. This is displayed to users after they start a remote client and run the Client Installation Wizard.
    10. Click Next, click Finish, and then click Done.
    Back to the top
    Authorize RIS in Active Directory

    After you install RIS, the RIS server must be authorized in Active Directory. Authorization determines control of which RIS servers can serve client computers on the network. If the RIS server is not authorized in Active Directory, client computers that request service cannot contact the RIS server.

    NOTE: To authorize a RIS server in Active Directory, you must be logged on as an enterprise administrator or a domain administrator of the root domain.
    1. Click Start, point to Administrative Tools, and then click DHCP.
    2. In the left pane, right-click DHCP, and then click Manage Authorized Servers.
    3. If your server is not listed, click Authorize, type the name or the IP address of the RIS server, and then click OK.

      NOTE: If you are prompted to confirm the RIS server, verify the name and IP address, and then clickOK.
    4. Click Close, and then quit the DHCP console.
    Back to the top
    Set User Permissions

    With RIS, clients can install their own client operating system. The users must also be granted permissions for creating computer accounts in the domain. To make it possible for users to create computer accounts anywhere in the domain:
    1. Click Start, point to Administrative Tools, and then click Active Directory Users and Computers.
    2. In the left pane, right-click your domain name, and then click Delegate Control.
    3. In the Delegation of Control Wizard, click Next.
    4. Click Add.
    5. Type the name of the group that requires permission to add computer accounts to the domain, and then click OK.
    6. Click Next.
    7. Click to select the Join a computer to the domain check box, and then click Next.
    8. Click Finish.
    Back to the top
    Install Clients By Using RIS

    This section describes how to install a client operating system on a computer that contains a network adapter that supports PXE DHCP-based boot ROM. To install a client operating system:
    1. Make sure that the network adapter is set as the primary boot device in the computer BIOS.
    2. Restart the client computer from the network adapter.
    3. When you are prompted to do so, press F12 to start the download of the Client Installation Wizard.
    4. At the "Welcome" screen, press ENTER.
    5. Type a user name that has permissions to add computer accounts to the domain, and then type the domain name and password for this user.
    6. Press ENTER.
    7. When you receive a warning message that states that all data on the client computer hard disk will be deleted, press ENTER.
    8. A computer account and a global unique ID for this workstation are displayed. Press ENTER to start Setup.
    9. If you are prompted to do so, follow the instructions on the screen to complete the client operating system installation.
    Back to the top
    Remote Installation Boot Disk Option

    You can use the remote installation boot disk with computers that do not contain a network adapter that supports PXE DHCP-based boot ROM. The boot disk is designed to simulate the PXE startup process.

    Rbfg.exe is a utility for creating network installation disks, and it is located in the RemoteInstall\Admin folder on every RIS server.

    Back to the top
    Creating a Boot Disk By Using the Windows Remote Boot Disk Generator

    To create a remote installation boot disk:
    1. Locate the drive:\RemoteInstall\Admin\I386 folder on the RIS server, where drive is the drive on which RIS is installed.
    2. Double-click the Rbfg.exe file.
    3. Put a floppy disk in the floppy disk drive, and then click Create Disk.
    4. When you prompted to create another disk, click No, and then click Close.
    NOTE: To view a list of supported network adapters, click Adapter List. You cannot add network adapters to this list.


    arash3400 و exxtreme سپاسگزاری کرده‌اند.

  5. #5
    نام حقيقي: رضا

    خواننده
    تاریخ عضویت
    Jan 2012
    محل سکونت
    تهران
    نوشته
    574
    سپاسگزاری شده
    141
    سپاسگزاری کرده
    511
    تو ویندوز کامپوننت چیزی به این نام وجود نداره.


    arash3400 سپاسگزاری کرده است.

  6. #6
    نام حقيقي: amir

    عضو عادی شناسه تصویری eng_amir68
    تاریخ عضویت
    Jul 2010
    محل سکونت
    tehran
    نوشته
    295
    سپاسگزاری شده
    171
    سپاسگزاری کرده
    93
    مطمئنی؟؟؟مگه میشه؟؟میخوایی فیلمشو برات بزارم؟؟


    arash3400 و exxtreme سپاسگزاری کرده‌اند.

  7. #7
    نام حقيقي: رضا

    خواننده
    تاریخ عضویت
    Jan 2012
    محل سکونت
    تهران
    نوشته
    574
    سپاسگزاری شده
    141
    سپاسگزاری کرده
    511
    نقل قول نوشته اصلی توسط eng_amir68 نمایش پست ها
    مطمئنی؟؟؟مگه میشه؟؟میخوایی فیلمشو برات بزارم؟؟
    نداره والا.
    دوست عزیز شما خودت تا حالا از این روش نصب کردی؟اگر اره یه توضیحی بده دمت گرم.


    arash3400 سپاسگزاری کرده است.

  8. #8
    نام حقيقي: محمد فراهانی

    عضو عادی شناسه تصویری mohamad-23
    تاریخ عضویت
    Nov 2011
    محل سکونت
    تهران
    نوشته
    1,303
    سپاسگزاری شده
    1096
    سپاسگزاری کرده
    847
    براي wds بايد كارت شبكه شما قابليت PXE-compliant رو ساپورت كنه . wds رو سرور نصب ميكني . براي اطلاع دقيق تر ميتوني به كتاب
    configurin windows 7 يا همون 680-70 از انتشارات microsoft مراجعه كني كه كامل wds رو توضيح داده.
    ضمنا علاوه بر روش wds مايكروسافت يه روش ديگه هم داره : Using a Network Share as an Installation Source كه براي اين حالت بايد سيستم به محيط PE بوت بشه و از اونجا به شبكه و فايل setup.exe دسترسي ژيدا كنه . كه البته مايكروسافت wds رو ارجح دونسته به اين روش

    نقل قول نوشته اصلی توسط exxtreme نمایش پست ها
    تو ویندوز کامپوننت چیزی به این نام وجود نداره.
    تو ويندوز كلاينتي كه نيست . تو نسخه سرور توي Role ها هستش فكر ميكنم


    ویرایش توسط mohamad-23 : 2012-02-07 در ساعت 09:05 PM
    arash3400، eng_amir68، shie و 1 نفر دیگر سپاسگزاری کرده‌اند.

  9. #9
    نام حقيقي: مهدی

    عضو عادی شناسه تصویری mahdi2008
    تاریخ عضویت
    Feb 2009
    محل سکونت
    ایران
    نوشته
    190
    سپاسگزاری شده
    109
    سپاسگزاری کرده
    185
    یک راه هم اینه که روی یک سیستم پارتیشن بندی و ویندوز و تمام نرم افزار های مورد نیاز رو نصب کنی بعد با norton ghost یک دیسک تو دیسک کنی و یا یک ایمیج از اون بگیری و روی فلش بریزی و روی سیستم های دیگه دقیقا بالا بیاری!
    من خودم زیاد از این کار استفاده کردم ، سریع و راحته.


    exxtreme سپاسگزاری کرده است.

  10. #10
    نام حقيقي: رضا

    خواننده
    تاریخ عضویت
    Jan 2012
    محل سکونت
    تهران
    نوشته
    574
    سپاسگزاری شده
    141
    سپاسگزاری کرده
    511
    نقل قول نوشته اصلی توسط mohamad-23 نمایش پست ها
    براي wds بايد كارت شبكه شما قابليت PXE-compliant رو ساپورت كنه . wds رو سرور نصب ميكني . براي اطلاع دقيق تر ميتوني به كتاب
    configurin windows 7 يا همون 680-70 از انتشارات microsoft مراجعه كني كه كامل wds رو توضيح داده.
    ضمنا علاوه بر روش wds مايكروسافت يه روش ديگه هم داره : Using a Network Share as an Installation Source كه براي اين حالت بايد سيستم به محيط PE بوت بشه و از اونجا به شبكه و فايل setup.exe دسترسي ژيدا كنه . كه البته مايكروسافت wds رو ارجح دونسته به اين روش


    تو ويندوز كلاينتي كه نيست . تو نسخه سرور توي Role ها هستش فكر ميكنم
    تو سرور 2003 منظورم هست.
    نقل قول نوشته اصلی توسط mahdi2008 نمایش پست ها
    یک راه هم اینه که روی یک سیستم پارتیشن بندی و ویندوز و تمام نرم افزار های مورد نیاز رو نصب کنی بعد با norton ghost یک دیسک تو دیسک کنی و یا یک ایمیج از اون بگیری و روی فلش بریزی و روی سیستم های دیگه دقیقا بالا بیاری!
    من خودم زیاد از این کار استفاده کردم ، سریع و راحته.
    دوست عزیز اگر سخت افزار کامپیوتر ها مثل هم نباشند چی کار کنم؟



  11. #11
    نام حقيقي: amir

    عضو عادی شناسه تصویری eng_amir68
    تاریخ عضویت
    Jul 2010
    محل سکونت
    tehran
    نوشته
    295
    سپاسگزاری شده
    171
    سپاسگزاری کرده
    93
    دوست عزیز اینجوری مشکل SID نامبر و داری و اگر سخت افزار ها مثل هم نباشه restore نمی شه .صبر کنی فیلم آموزشیشو برات میزارم


    exxtreme سپاسگزاری کرده است.

  12. #12
    نام حقيقي: amir

    عضو عادی شناسه تصویری eng_amir68
    تاریخ عضویت
    Jul 2010
    محل سکونت
    tehran
    نوشته
    295
    سپاسگزاری شده
    171
    سپاسگزاری کرده
    93
    فیلم آموزشی RIS امیدوارم که بتونی استفاده کنی
    01_configuring RIS server.avi - 4shared.com - file sharing - download movie file


    mahdi2008، hellion_m، shie و 1 نفر دیگر سپاسگزاری کرده‌اند.

  13. #13
    نام حقيقي: JaVaD

    عضو عادی شناسه تصویری mjzaret
    تاریخ عضویت
    Nov 2010
    محل سکونت
    شمال ايران
    نوشته
    515
    سپاسگزاری شده
    213
    سپاسگزاری کرده
    562
    نقل قول نوشته اصلی توسط exxtreme نمایش پست ها
    دوستان یک شبکه با 50 تا کلاینت و یه سرور با ویندوز سرور 2003 است.
    میخوام بدونم سریع ترین راه برای نصب ویندوز xp و تمام برنامهاش روی کلاینتها چیه؟
    یعنی میشه روی یکی xp و برنامه هارو نصب کرد بعد با ایمیج روی همشون بطور همزمان نصب کرد یا باید پشت هر کدوم نشست؟
    در ضمن روی کلاینتها هیچ ویندوزی نصب نیست و سخت افزار همشون هم مثل هم است.
    بهترين راه استفاده از RIS هست.

    البته اگه ايميج بگيري بايستي روي تك تك سيستم‌ها بري و نصبشمون كني.

    در RIS نيازي به اين كار نيست. فقط از قابليت شبكه استفاده مي‌كنيد و اقدام به نصب ويندوز مي‌كنيد.

    معايبي هم در RIS وجود داره و كمي كار رو مشكل مي‌كنه.

    يكي از اونها نشناختند درايور كارت شبكه كلاينت در هنگام نصب ويندوز هست.

    با توجه به تعداد كلاينتهاي شما استفاده از اين سرويس بهتر به نظر ميرسه.

    شاد باشيد




    exxtreme سپاسگزاری کرده است.

  14. #14
    نام حقيقي: علی حقیقی

    خواننده
    تاریخ عضویت
    Jul 2011
    محل سکونت
    تهران
    نوشته
    143
    سپاسگزاری شده
    42
    سپاسگزاری کرده
    54
    سلام
    از فرمایش همه اساتید مستفیض شدیم.
    فقط اگه میشه در مورد RIS توضیحاتی بدین
    اگه اینجا جای این سوال نبود بگید لطفا



  15. #15
    نام حقيقي: amir

    عضو عادی شناسه تصویری eng_amir68
    تاریخ عضویت
    Jul 2010
    محل سکونت
    tehran
    نوشته
    295
    سپاسگزاری شده
    171
    سپاسگزاری کرده
    93
    نقل قول نوشته اصلی توسط Xtfine نمایش پست ها
    فقط اگه میشه در مورد RIS توضیحاتی بدین
    RIS یکی از سرویس های ماکروسافتی است که به شما این اجازه رو میده که روی همه ی سیستم های شبکه تون ویندوز نصب کنید و دیگه نیازی نیست که تک تک روی همه ی کلاینت ها ویندوز نصب کنید در کل سرویس خوبیه.فیلم آموزشی رو هم که براتون گذاشتم.اگر مشکلی داشتید در خدمتتون هستم.



کلمات کلیدی در جستجوها:

نصب ویندوز از طریق شبکه

نصب ویندوز 7 از طریق شبکه

نصب wds

آموزش wds

hide network adapter windows server برایnLite کلاینتنحوه نصب WDSduplication wds روشهای نصب ویندوزنصب ویندوز از روی شبکهبوت از طریق شبکهروش نصب ویندوز از طریق شبکهنصب ویندوز7 از طریق شبکهنصب ویندوز با استفاده از شبکهنصب ویندوز بااستفاده از network shareنصب ویندوز از طریق کارت شبکهطریقه نصب ویندوز 7 از روی ایمیج شبکهris networkطریقه اعمال پالیسی به کلاینتها در ویندوز سرور2008 از طریق سرورنصب ویندوز با استفاده از Network Shareنصب ویندوز به روش risنصب ویندوز از طریق risنصب ویندوز با روش wdsکارت شبکه pxeدانلود آموزش نصب ویندوز7 از طریق شبکهنصب ویندوز از طریق شبکه pxe

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •