سلام به همه
پس از تلاش و جستجو بلاخره تنظيمات زير رو انجام دادم و ايوان بالا امد ولي يك مشكلي كه دارم اين هست كه يوزرها نميتون لاگين كنن طبق فرمايش اقاي حكيمي تمام لوگهاي تك پلاس رو هم فعال كردم و هيچ لوگي رخ نمي ده كه نشان از ارتباط داشته باشه
ممنون مي شم كه كمك كنيد اين مشكل حل بشه
باتشكر
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname as5300
no logging console
aaa new-model
aaa authentication ppp default none
aaa authentication ppp nttac group radius local
aaa authorization network default none
aaa authorization network nttac group radius local
aaa accounting update newinfo
aaa accounting network nttac start-stop group radius
enable secret level 7 5 $1$9DQk$anVySRulueTUcUnrhQ/j50
enable password 888888888
username mhnj password 0 999999999
username router2 privilege 15 password 0 88888
spe 1/0 1/9
firmware location system:/ucode/mica_port_firmware
!
resource-pool disable
!
call rsvp-sync
ip subnet-zero
ip rcmd rsh-enable
ip rcmd remote-host SYSTEM <IP valid NIC raduis server > SYSTEM enable
ip name-server 4.2.2.4
ip name-server 192.9.9.3
ip name-server 195.146.32.2
ip name-server 195.146.32.66
!
isdn switch-type primary-net5
isdn voice-call-failure 0
!
!
!
fax interface-type modem
mta receive maximum-recipients 0
!
controller E1 0
framing NO-CRC4
clock source line primary
line-termination 75-ohm
ds0-group 1 timeslots 1-15,17-31 type r2-digital
cas-custom 1
!
controller E1 1
framing NO-CRC4
clock source line secondary 1
ds0-group 1 timeslots 1-15,17-31 type r2-digital
cas-custom 1
!
controller E1 2
clock source line secondary 2
!
controller E1 3
clock source line secondary 3
!
controller E1 4
framing NO-CRC4
ds0-group 1 timeslots 1-15,17-31 type r2-digital
cas-custom 1
!
controller E1 5
clock source line secondary 5
!
controller E1 6
clock source line secondary 6
!
controller E1 7
clock source line secondary 7
!
!
!
interface Ethernet0
ip address 192.168.0.1 255.255.255.0
!
interface Serial0
no ip address
shutdown
no fair-queue
clock rate 2015232
!
interface Serial1
ip unnumbered FastEthernet0
ip access-group 115 in
ip access-group 115 out
no fair-queue
!
interface Serial2
no ip address
shutdown
no fair-queue
clock rate 2015232
!
interface Serial3
no ip address
shutdown
no fair-queue
clock rate 2015232
!
interface FastEthernet0
ip address < ip valied >
no ip mroute-cache
duplex full
speed 100
no cdp enable
!
interface Group-Async1
ip unnumbered FastEthernet0
ip access-group 116 in
ip access-group 116 out
encapsulation ppp
ip tcp header-compression
async mode interactive
peer default ip address pool Invalidpool
ppp authentication pap nttac
ppp authorization nttac
ppp accounting nttac
group-range 1 120
!
ip local pool Invalidpool 192.168.0.20 192.168.0.140
ip nat inside source list 1 interface Serial1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Serial1
no ip http server
ip pim bidir-enable
!
access-list 1 permit 192.168.0.0 0.0.0.255
access-list 115 deny tcp any any eq 135
access-list 115 deny tcp any any eq 139
access-list 115 deny tcp any any range 135 139
access-list 115 deny tcp any any eq 445
access-list 115 deny tcp any any eq 593
access-list 115 deny tcp any any eq 4444
access-list 115 deny udp any any eq 1434
access-list 115 deny tcp any any eq 1434
access-list 115 deny udp any any eq netbios-ns
access-list 115 deny udp any any eq netbios-dgm
access-list 115 deny udp any any eq netbios-ss
access-list 115 deny udp any any range 995 999
access-list 115 deny udp any any eq ntp
access-list 115 permit ip any any
access-list 115 deny tcp any any eq telnet
access-list 115 deny tcp any any eq ftp
access-list 116 deny icmp any any echo
access-list 116 deny icmp any any echo-reply
snmp-server community downtown RW 15
!
radius-server configure-nas
radius-server host <ip valid server > auth-port 1645 acct-port 1646
radius-server retransmit 3
radius-server timeout 7
radius-server deadtime 10
!
line con 0
transport preferred telnet
line 1 120
no flush-at-activation
modem answer-timeout 180
modem InOut
modem autoconfigure discovery
transport preferred none
transport input all
transport output none
autoselect during-login
autoselect ppp
line aux 0
line vty 0 4
password 888888888
!
end