-
مشکل با ماژول HWIC-1ADSL
من یک ماژول hWIC-1ADSL دارم که روی یک روتر 1841 نصبش کردم و خط ADSL رو به پورتش زدم ولی متاسفانه چراغ CD کارت ADSL ثابت نمی شه کسی از بچه ها در این مورد تجربه ای داره؟ در صورت امکان لطفا منو راهنمایی کنید که بتونم مشکلم رو حل کنم.
[LEFT][CODE][COLOR=#333333][FONT=Arial]ATM0/0/0 is down, line protocol is down[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Hardware is HWIC-DSLSAR (with Alcatel ADSL Module), address is 6412.2530.e4c8 (bia 6412.2530.e4c8)[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] MTU 4470 bytes, sub MTU 4470, BW 2048 Kbit/sec, DLY 250 usec,[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] reliability 0/255, txload 1/255, rxload 1/255[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Encapsulation ATM, loopback not set[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Keepalive not supported[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Encapsulation(s): AAL5[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 23 maximum active VCs, 256 VCs per VP, 0 current VCCs[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] VC Auto Creation Disabled.[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] VC idle disconnect time: 300 seconds[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Last input never, output never, output hang never[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Last clearing of "show interface" counters never[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Queueing strategy: Per VC Queueing[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 5 minute input rate 0 bits/sec, 0 packets/sec[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 5 minute output rate 0 bits/sec, 0 packets/sec[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 0 packets input, 0 bytes, 0 no buffer[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] Received 0 broadcasts (0 IP multicasts)[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 0 runts, 0 giants, 0 throttles[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 0 packets output, 0 bytes, 0 underruns[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 0 output errors, 0 collisions, 2 interface resets[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 0 unknown protocol drops[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial] 0 output buffer failures, 0 output buffers swapped out[/FONT][/COLOR][/CODE]
[QUOTE]
[COLOR=#333333][FONT=Arial]show dsl int atm 0/0/0
[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial]ATM0/0/0
Alcatel 20190 chipset information[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial]Line has not yet been activated.[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial]Modem Status: Down (DMTDSL_DO_OPEN)
DSL Mode: Unknown
Interrupts: 318704 (0 spurious)
PHY Access Err: 0
Activations: 0
LED Status: OFF
LED On Time: 0
LED Off Time: 0
Init FW: init_AMR_4.0.018.bin
Operation FW: AMR-E-4.0.018.bin
FW Source: external
[/FONT][/COLOR]
[COLOR=#333333][FONT=Arial]DSL: Training log buffer capability is not enabled[/FONT][/COLOR]
[/QUOTE]
[/LEFT]
با تشکر
-
کانفیگی که من زدم و جواب نمیده:
[LEFT][CODE]
interface ATM0/0/0
no ip address
no ip route-cache
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname <username>
ppp chap password 0 *********
ppp pap sent-username <username> password 0 *********
!
[/CODE]
[/LEFT]