نمایش نتایج: از شماره 1 تا 5 از مجموع 5
سپاس ها 1سپاس

موضوع: نصب ios روی سوئیج 2960

  
  1. #1
    نام حقيقي: shima

    تازه وارد
    تاریخ عضویت
    Nov 2014
    محل سکونت
    tehran
    نوشته
    20
    سپاسگزاری شده
    1
    سپاسگزاری کرده
    9

    نصب ios روی سوئیج 2960

    سلام
    من یک 2960 دارم که IOSش پریده ، میخوام IOS رو نصب کنم ولی نمیدونم:
    1- نرم افزار Xmodem رو از کجا میتونم دانلود کنم ؟
    2- چطور باید از Xmodem برای ارتقاء IOS سوئیچ استفاده کنم؟
    پیشاپیش سپاسگذارم



    موضوعات مشابه:

  2. #2
    نام حقيقي: احمد دستاویز

    عضو عادی شناسه تصویری dastaviz
    تاریخ عضویت
    Feb 2011
    محل سکونت
    طهران
    نوشته
    122
    سپاسگزاری شده
    88
    سپاسگزاری کرده
    22

  3. #3
    نام حقيقي: shima

    تازه وارد
    تاریخ عضویت
    Nov 2014
    محل سکونت
    tehran
    نوشته
    20
    سپاسگزاری شده
    1
    سپاسگزاری کرده
    9
    نقل قول نوشته اصلی توسط dastaviz نمایش پست ها
    علیک سلام دوست عزیز
    در قسمت "فهرست مطالب کاربردی بخش Cisco" یه قسمت مرتبط به مشکل من هست به نام "نصب IOS بر روی روتر در محیط ROMMON" که در این قسمت فقط یک پست وجود دارده به نام"خراب شدن IOS" که هیچ مطلب مفیدی نداره.......



  4. #4
    نام حقيقي: kaRim ParaVand

    عضو ویژه شناسه تصویری paravand20
    تاریخ عضویت
    Nov 2010
    محل سکونت
    Busher
    نوشته
    1,324
    سپاسگزاری شده
    1231
    سپاسگزاری کرده
    786
    نوشته های وبلاگ
    1
    نقل قول نوشته اصلی توسط Shima2014 نمایش پست ها
    سلام
    من یک 2960 دارم که IOSش پریده ، میخوام IOS رو نصب کنم ولی نمیدونم:
    1- نرم افزار Xmodem رو از کجا میتونم دانلود کنم ؟
    2- چطور باید از Xmodem برای ارتقاء IOS سوئیچ استفاده کنم؟
    پیشاپیش سپاسگذارم
    xmodem همون هاپر ترمینال هست
    در زمان استفاده bunde rate 11000 تغییر بده سرعت ارسال بره بالا تر


    Shima2014 سپاسگزاری کرده است.

  5. #5
    نام حقيقي: سام

    خواننده
    تاریخ عضویت
    Sep 2012
    محل سکونت
    tehran
    نوشته
    313
    سپاسگزاری شده
    60
    سپاسگزاری کرده
    205
    نقل قول نوشته اصلی توسط Shima2014 نمایش پست ها
    سلام
    من یک 2960 دارم که IOSش پریده ، میخوام IOS رو نصب کنم ولی نمیدونم:
    1- نرم افزار Xmodem رو از کجا میتونم دانلود کنم ؟
    2- چطور باید از Xmodem برای ارتقاء IOS سوئیچ استفاده کنم؟
    پیشاپیش سپاسگذارم
    سلام
    دوست من شما اول ios سوییچ را دانلود کن . بعد از طریق hyper terminal اون را انتقال بده

    Step 1 From your PC, download the software image tar file (image_filename.tar) from Cisco.com.
    The Cisco IOS image is stored as a bin file in a directory in the tar file. For information about locating the software image files on Cisco.com, see the release notes.
    Step 2 Extract the bin file from the tar file.

    Step 3 Connect your PC with terminal-emulation software supporting the Xmodem Protocol to the switch console port.
    Step 4 Set the line speed on the emulation software to 9600 baud.
    Step 5 Unplug the switch power cord.
    Step 6 Press the Mode button and at the same time, reconnect the power cord to the switch.
    You can release the Mode button a second or two after the LED above port 1 goes off. Several lines of information about the software appear along with instructions:
    The system has been interrupted prior to initializing the flash file system. The following
    commands will initialize the flash file system, and finish loading the operating system
    software#



    flash_init

    load_helper

    boot

    Step 7 Initialize the flash file system:
    switch: flash_init



    Step 8 If you had set the console port speed to anything other than 9600, it has been reset to that particular speed. Change the emulation software line speed to match that of the switch console port.
    Step 9 Load any helper files:
    switch: load_helper



    Step 10 Start the file transfer by using the Xmodem Protocol.
    switch: copy xmodem: flash:image_filename.bin



    Step 11 After the Xmodem request appears, use the appropriate command on the terminal-emulation software to start the transfer and to copy the software image into flash memory.
    Step 12 Boot the newly downloaded Cisco IOS image.
    switch:boot flash:image_filename.bin



    Step 13 Use the archive download-sw privileged EXEC command to download the software image to the switch.
    Step 14 Use the reload privileged EXEC command to restart the switch and to verify that the new software image is operating properly.
    Step 15 Delete the flash:image_filename.bin file from the switch.





کلمات کلیدی در جستجوها:

نصب ios روی سویچها سیسکو

نصب ios بر روی سوئیچ سیسکو

نصب ios روی روتر سیسکو

دانلود نرم افزار xmodem

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •