بالا نيامدن AS5300

با سلام دوستان من ديشب روترم برق رفت خاموش شد الان كه روشن ميكنم فكر كنم
IOS پريده رال اور زدم روتر رو كه با كابل كنسول
IOS ست آپ كنم تا اين مرحله مياد ديگه عكس العملي نشون نميده ممنون ميشم راهنمايي كنيد چي كار كنم
[CODE]System Bootstrap, Version 12.0(2)XD1, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
AS5300 platform with 131072 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x151c9c
Self decompressing the image : #################################################
################################################### [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-BOOT-M), Version 12.0(4)T1, RELEASE SOFTWARE (fc1
)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Tue 18-May-99 13:58 by kpma
Image text-base: 0x600088F8, data-base: 0x60272000
[/CODE][LEFT]
[/LEFT]

ببینید میتونید وارد حالت ریکاوری بشید ؟ (confreg 0x2142)

چه جوری باید این کار رو بکنم استاد ؟

[QUOTE=robocup;412214]چه جوری باید این کار رو بکنم استاد ؟[/QUOTE]

موقعی که داره بوت میشه کلید break رو پشت سرهم فشار بده

وارد mon ميشم ميشه راهنمايي بفرماييد از اينجا به بعد بايد چي كار كنم دستور شما هم اجرا كردم كه گفته بوديد
confreg 0x2142
الان بايد چي كار كنم
تشكر

[LIST=1][*]Establish a Console Session with the router.[*]If you can access the router, type [B]show version[/B] and record the configuration register ([B]0x2102[/B])[*]Use the power switch in order to turn off and then turn the router back on. Press Break on the terminal keyboard within 60 seconds of power up in order to put the router into ROMMON. ( Heyber Terminal: [B]Ctrl+break[/B] , minicom: [B]Ctrl-a f[/B] )[*]Type [B]confreg 0x2142[/B] at the rommon 1> prompt in order to boot from Flash.[*]Type [B]reset[/B] at the rommon 2> prompt.[*]Press [B]Ctrl-C[/B] in order to skip the initial setup procedure.[*]Type [B]enable[/B] at the Router> prompt.[*]Type [B]copy startup-config running-config[/B] in order to copy the nonvolatile RAM (NVRAM) into memory.[*]Now you can [B]change passwords[/B] and issue [B]no shutdown[/B] for every interface[*]Type config-register . ([B]config-register 0x2102[/B])[*]Press [B]Ctrl-z[/B] or end in order to leave the configuration mode.[*]Type [B]copy running-config startup-config[/B] in order to commit the changes.[/LIST]