Load Balance Between 2 Tunnel

سلام

یه 3560 داریم که یه لینک وایرلس از تهران به شعبه وصله بهش و لینک 20 مگه و روش تانل زدیم.

یه لینک وایرلس اینترنت 3مگ هم داریم به 3560 وصله و روش تانل زدیم.

هر دو سمت 3560 داریم.

eigrp رو هر دو روتر فعاله. و داره روتینگ انحجام میشه.

میخام load balance کنم. با تغییر واریانس باید انجام بدم ؟ یا ip crf رو فعال کنم ؟ یا دستود per packet sharing ؟:eek:

هم با Variance میتونید و هم با Delay و Bandwidth

البته من تا به حال در دنیای واقعی این کار رو نکردم ، فقط در مجازی سازی تست کردم !

با واریانس سخته ! اینطور نیست ؟
اگه BW بزنم باید هردوشو یه عدد بذارم دیگه ؟ مثلا هردو 10مگ؟ درسته؟

حالا بخام لینک با پهنای بیشتر اکتیو باشه و لینک با پهنای کمتر ریداندنت باشه چی؟

[QUOTE=greatcyrus;404866]با واریانس سخته ! اینطور نیست ؟
[/QUOTE]

بله !
کمی مشکل هست !

[QUOTE=greatcyrus;404866]
اگه BW بزنم باید هردوشو یه عدد بذارم دیگه ؟ مثلا هردو 10مگ؟ درسته؟
[/QUOTE]

بله
Delay هم باید تنظیم کنید !

نحوه محاسبه Variance :
[LEFT][QUOTE]
I think I've finally got a handle on this and wanted to share what I've learned about the [I]variance [/I]command in particular, but also about successors, feasible successors, and reported distance. It's a long read, but hopefully someone whose trying to understand the EIGRP [I]variance [/I]command will find this useful. Please reply to this post if you find any mistakes:

[B]Note: [/B]In this article, RD (reported distance) means the same thing as AD (advertised distance). You may come across one or the other in books or on web sites.


[URL="https://learningnetwork.cisco.com/servlet/JiveServlet/showImage/2-236859-109950/Capture.JPG"][IMG]https://learningnetwork.cisco.com/servlet/JiveServlet/downloadImage/2-236859-109950/450-215/Capture.JPG[/IMG][/URL]

[COLOR=#000000]By default, in order to load-balance over different paths, the metrics of those paths must match [/COLOR][COLOR=#000000][B]exactly[/B][/COLOR][COLOR=#000000].In the network shown above, all bandwidth and delay settings were identical across both paths. I then went into R4 and changed the delay on s0/2 to 2001 (the default is 2000, or 20000 usec). When I did that, R1 would no longer used the path through R4, as the metrics were no longer equal. This proves that [/COLOR][COLOR=#000000]EIGRP wants to see metrics that are [/COLOR][COLOR=#000000][B]exactly [/B][/COLOR][COLOR=#000000]the same across multiple paths before it will load balance (when [/COLOR][COLOR=#000000][B]not [/B][/COLOR][COLOR=#000000]using the [/COLOR][COLOR=#000000][I]variance [/I][/COLOR][COLOR=#000000]command). [/COLOR]
[COLOR=#000000]
[/COLOR]
[COLOR=#0099ff][B]Use of Variance[/B][/COLOR]
[COLOR=#0099ff][/COLOR]
When using the variance command, eigrp will add a feasible successor to the route table [B]if[/B] the feasible successor has a feasible distance that is less than or equal to the product of the feasible distance of the successor times the variance setting [B]and[/B] the feasibility condition is met. In math terms:

FD (of the FS) [B]<=[/B] FD (of the S) * [I]variance [/I]


[LIST][*]FD – feasible distance[*]FS – feasible successor[*]S – successor[/LIST]
[COLOR=#ff0000]For variance to work, the route must [/COLOR][COLOR=#ff0000][B]already [/B][/COLOR][COLOR=#ff0000]be a feasible successor. A route becomes a feasible successor by meeting the feasibility condition. [/COLOR]Then, if variance is configured and the variance logic is met, the route is added to the routing table (this is explained in more detail later). When we say "the variance logic is met", we mean that the FD of the FS is less than or equal to the product of the successor's FD*[I][COLOR=#0000ff][I]variance-value [/I][COLOR=#000000](the value configured with the [I]variance[/I] command)[/COLOR][/COLOR][I]:[/I][/I]
[COLOR=#0000ff][I]The feasibility condition states that the reported distance (RD) of a route must be [/I][U][B]less than[/B][/U][I] the feasible distance of the current successor route (the feasible successor). In other words, in order to become a feasible successor (FS), the reported distance of the feasible successor must be less than the feasible distance of the successor.[/I][/COLOR]
[COLOR=#000000][I] RD< FD (of the FS)[/I][/COLOR]

[B]To illustrate this, we'll perform all testing from R1's perspective, making changes in the delay settings in R4 only. With all routers set to their defaults (bandwidth and delay), R1 load balances across both paths to the 10.0.0.0 /8 network:[/B]
[FONT=Courier New]R1#ship route[/FONT]
[FONT=Courier New]D 10.0.0.0/8 [90/2707456] via 192.168.1.2, 00:04:00, Serial0/0[/FONT]
[FONT=Courier New][90/2707456]via 33.168.30.2, 00:04:00, Serial0/1[/FONT]

[FONT=Courier New]R1#showip eigrp top[/FONT]
[FONT=Courier New]P10.0.0.0/8, 2 successors, FD is 2707456[/FONT]
[FONT=Courier New]via33.168.30.2 (2707456/2195456), Serial0/1[/FONT]
[FONT=Courier New]via192.168.1.2 (2707456/2195456), Serial0/0[/FONT]
[B]After changing R4 s0/2 to a delay of 3000 (or 30000 usec):[/B]
Notice that since the two paths to reach the 10.0.0. /8 network are no longer equal, R1 no longer load balances across both paths (it only has one route to the 10.0.0.0 /8 network, via R2). Also notice that the topology table still has two entries for the 10.0.0.0/8 network, because the reported distance of 2451456 is still less than the feasible distance of the successor route (2707456):
[FONT=Courier New]R1#showip route [/FONT]
[FONT=Courier New]D 10.0.0.0/8 [90/[COLOR=#008000][B]2707456[/B][/COLOR]] via192.168.1.2, 04:43:17, Serial0/0[/FONT]

[FONT=Courier New]R1#showip eigrp topology[/FONT]
[FONT=Courier New]P10.0.0.0/8, 1 successors, FD is 2707456[/FONT]
[FONT=Courier New]via192.168.1.2 ([COLOR=#008000][B]2707456[/B][/COLOR]/2195456),Serial0/0[/FONT]
[FONT=Courier New]via33.168.30.2 ([COLOR=#000000]2963456[/COLOR]/[COLOR=#008000][B]2451456[/B][/COLOR]),Serial0/1 [/FONT]
[FONT=Courier New]
[/FONT]
[B]Now, we work with the [/B][I]variance [/I][B]command to force eigrp to load-balance across two unequal-cost paths. [/B]
To determine what value to use for the [I]variance [/I]command, we first divide the FD of the backup route (FS) by the FD of the successor route:

[COLOR=#008000][FONT=Courier New][B]2963456[/B][/FONT][/COLOR][COLOR=#0000ff][FONT=Courier New][B]/[/B][/FONT][/COLOR][COLOR=#008000][FONT=Courier New][B]2707456= 1.095 [/B][/FONT][/COLOR]
[COLOR=#008000][FONT=Courier New][/FONT][/COLOR]
Our multiplier is 1.095 (it's greater than 1, so we need to round up to the next whole number, or [B]2[/B].). So, we now go into the eigrp routing process and configure the [I]variance [/I]command:

r1(config)#router eigrpx
r1(config-router)#variance 2

This tells EIGRP to take the feasible distance of every successor in the topology table and multiply that value by 2. Now, all feasible successors which are less than or equal to the FD*2 (that's the FD of the successor * 2) will be placed into the route table. Sticking with R1 and its path to the 10.0.0.0 /8 network, we take 2*2707456 (the FD of our successor), which give us 5414912. Now, any backup route (feasible successor) whose FD is less than 5414912 will be placed into the route table[COLOR=#333333] ([/COLOR][U]as long as its reported distance is less than the feasible distance of the successor route, which will be explained further in a minute[/U][COLOR=#333333]).[/COLOR]
[COLOR=#ff0000]
[/COLOR]
So, since the FD of the backup route (2963456) is less than 2*FD of the successor route ([COLOR=#008000][FONT=Courier New][B]2707456*2 or 5414912)[/B][/FONT][/COLOR], [COLOR=#ff0000][B]AND[/B][/COLOR], the RD of its backup route ([COLOR=#008000][FONT=Courier New][B]2451456)[/B][/FONT][/COLOR]is less than the FD of the successor ([COLOR=#008000][FONT=Courier New][B][FONT=Courier New]2707456)[/FONT][COLOR=#000000],[/COLOR][FONT=Courier New] [/FONT][/B][/FONT][/COLOR]that route is now placed back into the routing table:

[FONT=Courier New]R1#[/FONT]
[FONT=Courier New]D 10.0.0.0/8 [90/2707456] via 192.168.1.2, 00:00:02, Serial0/0[/FONT]
[FONT=Courier New][90/2963456]via 33.168.30.2, 00:00:02, Serial0/1[/FONT]

[FONT=Courier New]R1#ship eigrp topo[/FONT]
[FONT=Courier New]P10.0.0.0/8, 1 successors, FD is 2707456[/FONT]
[FONT=Courier New]via192.168.1.2 (2707456/2195456), Serial0/0[/FONT]
[FONT=Courier New]via33.168.30.2 (2963456/2451456), Serial0/1 [/FONT][COLOR=#0000ff]→ backup route[/COLOR]
[FONT=Courier New] [COLOR=#008000][B]( FD / RD )[/B][/COLOR][/FONT]

Next, I modified the delay in R4 s0/2 to 4000. Notice what happens (the variance is still set at 2). R1 is no longer load-balancing across R2 and R4, and [COLOR=#ff0000]the topology table no longer has a feasible successor (backup route) listed.[/COLOR] Why? First, in order to view ALL the routes stored inthe topology table (successor, feasible successor , and non-successor routes), use the keyword [B]all-links [/B]after the [B]show ip eigrp topology [/B]command.

Now, we can see that R1 [B]does [/B]know about the path through R4 (via 33.168.30.2). In addition, thebackup route's FD of 3219456 is definitely less than 5414912 that we calculated earlier, so it “should” load balance across the two paths, right? [B]Wrong![/B] The reason R1 is NOT sending traffic across R4 is because the reported distance of the backup route is equal to the FD of the successor route (see highlight in red below). Therefore, it does [B]not [/B]meet the feasibility condition (i.e. the RD must be [U][B]less[/B][/U]than the FD of the successor) and will not be considered as a backup route, no matter how high you set the variance value. You could enter the command [I]variance 128 [/I]and it would have no effect, because there is no feasible successor in the topology table.

[FONT=Courier New]R1#show ip route[/FONT]
[FONT=Courier New]D 10.0.0.0/8 [90/2707456] via 192.168.1.2, 00:00:58, Serial0/0[/FONT]

[FONT=Courier New]R1#showip eigrp top[/FONT]
[FONT=Courier New]P10.0.0.0/8, 1 successors, FD is 2707456[/FONT]
[FONT=Courier New]via192.168.1.2 (2707456/2195456), Serial0/0[/FONT]

[FONT=Courier New]R1#show ip eigrp top [COLOR=#ff0000][B]all-links[/B][/COLOR][/FONT]
[FONT=Courier New]IP-EIGRPTopology Table for AS(5)/ID(192.168.1.1)[/FONT]

[FONT=Courier New]Codes:P - Passive, A - Active, U - Update, Q - Query, R - Reply,[/FONT]
[FONT=Courier New]r- reply Status, s - sia Status[/FONT]

[FONT=Courier New]P10.0.0.0/8, 1 successors, FD is 2707456, serno 192[/FONT]
[FONT=Courier New]via192.168.1.2 ([COLOR=#ff0000][B]2707456[/B][/COLOR]/2195456),Serial0/0[/FONT]
[FONT=Courier New]via33.168.30.2 (3219456/[COLOR=#ff0000][B]2707456[/B][/COLOR]),Serial0/1[/FONT]



source : [URL]https://learningnetwork.cisco.com/thread/43785[/URL]
[/QUOTE]
[/LEFT]

[COLOR="silver"][SIZE=1]- - - ادامه - - -[/SIZE][/COLOR]


این هم بد نیست بدونید :

[QUOTE]

13-نکات کلیدی در مورد دستور Variance :

[LIST][*]مقدار Variance را باید در مقدار FD مربوط به مسیر Successor ضرب نمود[*]در صورتی که مقدار FD مربوط به هریک از مسیر های Feasible Successor کمتر از عدد حاصله باشد،مسیر ذکر شده در کنار مسیر اصلی در داخل جدول Routing قرار خواهد گرفت.البته تعدادمسیری که می تواند به این شکل در داخل جدول Routing قرار گیرد توسط دستور Maximum-paths نعیین می گردد.[*]مسیر هایی غیر از Successor و Feasible Successor در داخا جدول Routing قرار نمی گیرد.[/LIST]

[/QUOTE]

منبع : [URL]http://forum.ciscoinpersian.com/showthread.php?t=7100[/URL]

داداش ممنون. همون bw و delay رو که گفتی چه جوری ست کنم ؟

با دستور bandwidth و delay

[QUOTE=alisc;404994]با دستور bandwidth و delay[/QUOTE]

علی آقا ممنون

پس من الان یه لینک 20مگ و یه لینک 3مگ دارم برم زیر اون 3 مگی بزنم 20مگ؟

Delay لینک 20 مگی هم 20-25 میلی ثانیه اس . برم زیر 3 مگیه بزنم 25 میلی ثانیه ؟

[QUOTE=greatcyrus;404996]
پس من الان یه لینک 20مگ و یه لینک 3مگ دارم برم زیر اون 3 مگی بزنم 20مگ؟

Delay لینک 20 مگی هم 20-25 میلی ثانیه اس . برم زیر 3 مگیه بزنم 25 میلی ثانیه ؟[/QUOTE]

خدمتتون عرض کردم در دنیای واقعی این کار رو انجام ندادم ! ( تست ها فقط در پکت تریسر بوده )
تست کنید ببینید جواب میده ؟