نمایش نتایج: از شماره 1 تا 3 از مجموع 3
سپاس ها 1سپاس

موضوع: PRI error message : RAI detected

  
  1. #1
    نام حقيقي: Majid

    خواننده
    تاریخ عضویت
    Jan 2010
    محل سکونت
    Isfahan
    نوشته
    80
    سپاسگزاری شده
    27
    سپاسگزاری کرده
    34

    PRI error message : RAI detected

    با سلام به دوستان

    من روی روتر سیکو این خطا را دارم :

    Nov 12 17:53:19.841 INT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0:15, changed state to up
    Nov 12 17:53:20.133 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:21.209 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:22.221 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:23.625 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:24.633 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:25.649 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:26.657 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:50.969 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:51.977 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected





    این خطا مربوط به چی میشه ؟
    نکته جالب اینه که اینترفیس های سریال تعریف شده روی این E1 ، آپ هستند !!!



    موضوعات مشابه:
    ویرایش توسط SMajidCS : 2012-10-21 در ساعت 04:24 PM

  2. #2
    نام حقيقي: Armin Rezaeimehr

    مدیر عمومی شناسه تصویری EVERAL
    تاریخ عضویت
    Jul 2009
    محل سکونت
    Tehran
    نوشته
    695
    سپاسگزاری شده
    572
    سپاسگزاری کرده
    594
    نوشته های وبلاگ
    7
    نقل قول نوشته اصلی توسط SMajidCS نمایش پست ها
    با سلام به دوستان

    من روی روتر سیکو این خطا را دارم :

    Nov 12 17:53:19.841 INT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0:15, changed state to up
    Nov 12 17:53:20.133 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:21.209 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:22.221 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:23.625 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:24.633 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:25.649 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:26.657 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected
    Nov 12 17:53:50.969 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to up
    Nov 12 17:53:51.977 INT: %CONTROLLER-5-UPDOWN: Controller E1 1/0, changed state to down (RAI detected






    این خطا مربوط به چی میشه ؟
    نکته جالب اینه که اینترفیس های سریال تعریف شده روی این E1 ، آپ هستند !!!
    سلام
    The RAI failure is declared when the A-bit (bit three in timeslot zero of frames not containing Frame Alignment Signal [FAS]) becomes one (1). The RAI failure is not declared when a Loss of Signal (LoS) or LoF is detected.
    To correct rxRAI errors, complete these steps:

    1. Insert an external loopback cable into the port.
      For more information, see the Hard Plug Loopback Tests for E1 Lines document.
    2. Issue the show controller e1 EXEC command to determine if any alarms occur.
      If you do not find any alarms, then the local hardware is probably in good condition. In that case, complete these steps:
      1. Check the cabling. Ensure that you have correctly connected the cable between the interface port and the E1 service provider equipment or E1 terminal equipment. Ensure that you have connected the cable to the correct ports. Correct the cable connections if necessary.
      2. Check the cable integrity by looking for breaks or other physical abnormalities in the cable. Ensure the pinouts are set correctly. Replace the cable if necessary.
      3. Check the settings at the remote end and verify that they match your port settings.

        If the problem persists, contact your service provider.

    3. Remove the loopback plug, and reconnect your E1 line.
    4. Check the cabling.
    5. Power cycle the router.
    6. Connect the E1 line to a different port. Configure the port with the same settings as the line.

      If the problem does not persist, then the fault lies with the port. In this case, complete the following steps:
      1. Reconnect the E1 line to the original port.
      2. Perform a hardware loop test. For more information, see the Hard Plug Loopback Tests for E1 Lines document.


    E1 Alarm Troubleshooting
    https://supportforums.cisco.com/thread/199883





  3. #3
    نام حقيقي: محمد فراهانی

    عضو عادی شناسه تصویری mohamad-23
    تاریخ عضویت
    Nov 2011
    محل سکونت
    تهران
    نوشته
    1,303
    سپاسگزاری شده
    1096
    سپاسگزاری کرده
    847
    دوستان عزیز موضوعی بگم که شاید خالی از لطف نباشه گفتنش ...
    بعضی ها میپرسن چرا Device های سیسکو اینقدر گرون هستند !!!
    دوستان یکی از علتاش Support فوق العاده سیسکو از نظر نرم افزاری و سخت افزاری از محصولاتشه ...
    90 روز بازگشت محصول بدون چون و چرا و شبکه قوی پاسخگویی و نشر علم سیسکو ....
    شما هر سوالی که واستون پیش میاد اول برید توی سایت سیسکو سرچ کنید ... واقعا 95% اوقات جواب دقیق و مطمئن رو توی خود سایت پیدا خواهید کرد ...


    mavrick سپاسگزاری کرده است.

کلمات کلیدی در جستجوها:

rai detected

controller e1 rai detected

changed state to down rai detected cisco

controller-5-updown: controller e1 10 changed state to down (rai detected)

changed state to down (rai detected)

controller-5-updown controller e1 changed state to down (rai detected)

controller e1 سیسکو

cisco lof detected

controller-5-updown (rai detected)

controller-5-updown rai detected

rai detected e1

controller e1 cisco

controller e1 far end block errors detected

مشکل Unusual traffic from your computer network

ais detected e1 di cisco

rai detected cisco

nov 12 17:53:19.841 int: lineproto-5-updown: line protocol on interface serial10:15 changed state to up nov 12 17:53:20.133 int: controller-5-updown: controller e1 10 changed state to down (rai detected

pri controller-5-updown: controller e1 0 changed state to up troubleshooting

CONTROLLER-5-UPDOWN: (RAI detected)

pri errors rai

controllers e1 far end block errors detected

e1 issue lof detected

pri error message (rai detected)

cisco e1 controller rai detected -ais

e1 controller far end block errors detected

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •