نمایش نتایج: از شماره 1 تا 2 از مجموع 2
سپاس ها 2سپاس

موضوع: NAT and routing on 3560

  
  1. #1
    نام حقيقي: Saeed

    عضو عادی شناسه تصویری greatcyrus
    تاریخ عضویت
    Jan 2010
    محل سکونت
    Tehran
    نوشته
    2,662
    سپاسگزاری شده
    933
    سپاسگزاری کرده
    1248
    نوشته های وبلاگ
    3

    NAT and routing on 3560

    درود بر همگي

    آقا اين چه فروميه! ملت با كنايه به آدم جواب ميدن!يه سر بريد تو فرومهاي خارجي ببنيد چه طوريه!

    و اما سوال:

    1- اينكه تو 3560 چرا دستور nat رو قبول نميكنه:
    2- ميخام تو 3560 بر اساس source ip روت بزنم ميشه؟مثلا به جاي destination بگم از فلان ip يا اينترفيس اومد بره به فلان ip يا اينترفيس

    ميشه؟

    كسي هست بدونه؟

    مرسي



    موضوعات مشابه:

  2. #2
    نام حقيقي: Ali Afzalan

    مدیر بخش Cisco شناسه تصویری aliafzalan
    تاریخ عضویت
    Apr 2009
    محل سکونت
    Tehran
    نوشته
    2,086
    سپاسگزاری شده
    2557
    سپاسگزاری کرده
    2059
    سلام
    در مورد شماره 1 که باید از سیسکو بپرسید! (و البته آقای نجاتی زاده هم توی NAT بر اساس سورس آي پي به این موضوع اشاره کردند)
    در مورد شماره 2 هم:


    Route-maps allow to you deal with traffic on your router by policy rather than traditional means.

    In this example, we will route traffic by source address, or who is sending the traffic, rather than by destination, or where the traffic is going. Typically routers just look at where traffic is headed, compare that destination to their routing table and send the packets on their way. To override basic routing on a Cisco router, a route-map configuration is required.

    What are route-maps?
    Essentially, Route-maps are like a scripting language for routers. They define traffic and then process it according to a defined list of statements almost like a miniature computer program.

    Why would you want to route by source address?
    Perhaps you have internet connections from two internet service providers along with IP addresses provided by both and you want to send traffic from the IP address that belongs to each ISP to the correct internet connection. Another application of router-maps would be to migrate traffic from one firewall to another in steps rather than all at once. However traffic can be identified by any attribute likewhere it is going or by the TCP/IP port it uses for other examples.

    Understanding the Route-Map structure
    Route-maps inherit their structure from if-then statements in programming. First, it creates a step (10 and 20 in this example), matches a criteria in each step and then performs an action.

    route-map route-map-name permit 10
    match criteria-1
    set perform-action-1

    route-map route-map-name permit 20
    match criteria-2
    set perform-action-2

    Configuring the Route-Map for routing traffic by source
    Step1: Define the traffic with an access-List
    RouterA(config)#access-list 25 10.10.25.0 0.0.0.255

    Step 2: Create a Route-Map with an action
    RouterA(config)# route-map Traffic_to_ISP_A 10

    RouterA(config-route-map)#match ip 25

    RouterA(config-route-map)#set next hop 10.15.15.1

    Step 3: Apply the Route-Map to the router interface that the traffic enters into
    RouterA(config)#interface gig0/1
    RouterA(config-int)#ip policy Traffic_to_ISP_A



    http://www.associatedcontent.com/art...o_routers.html



    ویرایش توسط aliafzalan : 2011-03-13 در ساعت 11:55 AM
    SADEGH65 و al1p0ur سپاسگزاری کرده‌اند.

کلمات کلیدی در جستجوها:

کانفیگ سوییچ 3560

دستورات سوئیچ جهت عملیات routing 3560

سویچ 3560 سیسکو ip route

سوییچ 3560 routing

routing 3560

دستور ip routing در سوییچ 3560

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •