-
مشکل در tunnel
سلام من بین دو سویییچ 3560 و 3750 روی بستر اینترانت یک tunnel ایجاد کردم. از زمانی که این tunnel ایجاد شده است cpu usage به شدت بالا رفته است. یعنی وقتی که پهنای باند زیادی از تونل استفاده می شود cpu usage بالا می رود. تا حدود 90%.
config تونل هم به شرح زیر است:
ip address x.x.x.x x.x.x.x
tunnel source x.x.x.x
tunnel destination x.x.x.x
tunnel mode ipip
-
سلام
میشه کانفیگ و نسخه سوئیچ ها را بزارید ؟!؟
یعنی در شرایطی که پهنای باند کم هست، همه چیز ok هست و با بالا رفتن پهنای باند cpu usage بالا میره؟
خروجی sh int tunnel را هم بزارید.
-
این هم خروجی sh int tunnel 0
سوییچها یکی 3560 و دیگری 3750 و ios version 12.2.46 se advance ip service k9
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 172.19.19.1/29
MTU 1514 bytes, BW 100 Kbit, DLY 50000 usec,
reliability 255/255, txload 134/255, rxload 191/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 10.30.132.226, destination 10.8.176.2
Tunnel protocol/transport IP/IP, key disabled, sequencing disabled
Tunnel TTL 255
Checksumming of packets disabled, fast tunneling enabled
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 169
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 242000 bits/sec, 352 packets/sec
5 minute output rate 5698000 bits/sec, 532 packets/sec
86066744 packets input, 11392979639 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
112904742 packets output, 109882906705 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
-
کلا سوئیچ ها با tunneling مشکل دارند. اما به جای IP-IP از GRE استفاده کن. شاید با ارتقاء IOS حل بشه. شاید!! ب
-
[QUOTE=shabake_karan;266322]کلا سوئیچ ها با tunneling مشکل دارند. اما به جای IP-IP از GRE استفاده کن. شاید با ارتقاء IOS حل بشه. شاید!! ب[/QUOTE]
سلام
البته سوئیچ ها (3750 و 3550) با GRE هم مشکل دارند.
[LEFT][B] High CPU Utilization After Enabling GRE Tunnels [/B]
Generic Routing Encapsulation (GRE) tunnels are not supported on the Cisco Catalyst 3550 Switch. Even though the CLI commands are there to configure the GRE, it is not officially supported. Refer to the [URL="http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.1_19_ea1/configuration/guide/swuncli.html#wp1013363"]Unsupported VPN Configuration Commands[/URL] section of [URL="http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.1_19_ea1/configuration/guide/swuncli.html"]Unsupported CLI Commands for Catalyst 3550[/URL] for this information. The reason for this is that the Cisco Catalyst 3550 Switch uses hardware-based Cisco Express Forwarding (CEF) switching. There is no method to CEF-switch GRE packets. GRE packets must be encapsulated by the software. The hardware does not have the capability to encapsulate the packets. Consequently, this traffic is processed or software switched. The process or software switched traffic can quickly cause the CPU to spike
[HTML]http://ciscosystems.com/en/US/products/hw/switches/ps646/products_tech_note09186a008078ece1.shtml#Pr1[/HTML][RIGHT]
شاید مشکل دوستمون با IPIP هم به همین دلیل باشه.
[/RIGHT]
[/LEFT]
-
سلام
ببین من روی 3750 حدود 40 تانل داشتم و کار می کرد!!
اما 3560 قاط میزنه سعی کن 3560 رو عوض کنی.