-
error بر روی خطوط E1
از وقتی خطوط E1 من از cas ,971 به خطوط IN , pri شده 4 تا از خط های E1 روترم error داره
ثشقفا روتر رو چک کردم - کابل مودم تا روتر رو هم عوض کردم ! این وضعیت باعص میشه یوزر هایی که رو این خط ها میان کند باشن یا هر چیز دیگه ای که سریعا dc میشن !
[CODE]E1 7 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Version info of slot 0: HW: 1, PLD Rev: 11
Framer Version: 0x8
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x49,
Board Hardware Version 2.0, Item Number 800-3883-02,
Board Revision A0, Serial Number 15260399,
PLD/ISP Version 0.1, Manufacture Date 23-Aug-1999.
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line Secondary.
Data in current interval (861 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
4 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
4 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
[/CODE]
جالبی اینجاست که هر 4 تا خط تقریبا به یک اندازه error دارن
-
با توجه به Error ها شما ، اگر که دلیلش اونها باشه ، مفهمومه این error ها این هست .دلیل اینها می تونه که یکی از موارد زیر باشه :
[LEFT][ltr]
[B]Slip secs:
[/B]Indicates the replication or deletion of the payload bits of a domestic trunk interface (DS1) frame. A slip might happen when there is a difference between the timing of a synchronous receiving terminal and the received signal.
[B]Errored secs: [/B]
In ESF and E1 CRC links, an errored second is a second in which one of the following defects is detected:[LIST][*] One or more Path Code Violations.[*] One or more Controlled Slip events.[/LIST]For SF and E1 no-CRC links, the presence of Bipolar Violations also triggers an errored second.
[/ltr]
[RIGHT]که البته لینک شما no-crc هست و مورد پائینی در قسمت دوم را شامل می شود. با توجه به RFC شماره 1406 وجود ، Bipolar violation دلیلش این هست :
[LEFT]A BPV error event for a B8ZS- or HDB3-coded signal is the occurrence of a pulse of the same polarity as the previous pulse without being a part of
the zero substitution code
[RIGHT]بعد یک پیشنهاد اینکه خروجی show interface E1 7 را هم بگذار و دوهم اینکه ببین که ppp link quality برابر با چن هست و ببین که user ها وقتی که connect می شوند ، SNR خط برابر با چند هست و ببین که اصلا این برای همه فراگیر هست یا که فقط روی یک AS خاص اینجوریه و ...
[/RIGHT]
[/LEFT]
[/RIGHT]
[/LEFT]
-
[CODE]PoonakRouter#sh controllers e1 7
E1 7 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Version info of slot 0: HW: 1, PLD Rev: 11
Framer Version: 0x8
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x01, Board ID 0x49,
Board Hardware Version 2.0, Item Number 800-3883-02,
Board Revision A0, Serial Number 15260399,
PLD/ISP Version 0.1, Manufacture Date 23-Aug-1999.
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line Secondary.
Data in current interval (2 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
1 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
1 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Data in Interval 1:
0 Line Code Violations, 0 Path Code Violations
3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
3 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
3 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs[/CODE]
من حتی کابل خط e1 که به مودم موتصل شده رو هم عوض کردم !
این روتر 8 تا E1 داره 4 تای دیگه مشکلی ندارن حتی کابل هاشون رو با هم عوض کردم
ممنون ایمان جان اجازه بده من بقیه چیزا رو چک کنم اما اخرش میرسم به مخابرات !!