ممنون میشم یکی از دوستان کانفیگی رو که برای E1 PRI روی access server هست و از طرف مخابرات و مادمها خط تست شده بزاره.
فقط up شدن e1 کافیه.
Printable View
ممنون میشم یکی از دوستان کانفیگی رو که برای E1 PRI روی access server هست و از طرف مخابرات و مادمها خط تست شده بزاره.
فقط up شدن e1 کافیه.
[LEFT]version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname ***
!
aaa new-model
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authentication ppp default if-needed group tacacs+ local
aaa authorization exec default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local if-authenticated
aaa authorization network default group tacacs+ local
aaa accounting nested
aaa accounting update newinfo
aaa accounting exec default start-stop group tacacs+
aaa accounting network default start-stop group tacacs+
enable password reza
!
username admin password 0 ****i
spe 1/0 1/9
firmware location system:/ucode/mica_port_firmware
!
!
resource-pool disable
!
modem-pool *1
pool-range 1-30
called-number **** max-conn 30
called-number rsvp-sync max-conn 30
!
call rsvp-sync
ip subnet-zero
ip rcmd rsh-enable
ip rcmd remote-host system **** system enable
no ip domain-lookup
ip name-server ****
ip name-server ****
ip name-server ****
ip name-server 192.9.9.3
ip name-server ****
!
isdn switch-type primary-net5
isdn gateway-max-interworking
!
!
!
!
!
fax interface-type modem
mta receive maximum-recipients 0
!
controller E1 0
framing NO-CRC4
clock source line primary
pri-group timeslots 1-31
!
controller E1 1
clock source line secondary 1
!
controller E1 2
clock source line secondary 2
!
controller E1 3
clock source line secondary 3
!
controller E1 4
clock source line secondary 4
!
controller E1 5
clock source line secondary 5
!
controller E1 6
clock source line secondary 6
!
controller E1 7
clock source line secondary 7
!
!
!
interface Ethernet0
no ip address
shutdown
!
interface Serial0
no ip address
shutdown
no fair-queue
clockrate 2015232
!
interface Serial1
no ip address
shutdown
no fair-queue
clockrate 2015232
!
interface Serial2
no ip address
shutdown
no fair-queue
clockrate 2015232
!
interface Serial3
no ip address
shutdown
no fair-queue
clockrate 2015232
!
interface Serial0:15
ip unnumbered FastEthernet0
encapsulation ppp
ip mroute-cache
autodetect encapsulation ppp v120 lapb-ta
isdn switch-type primary-net5
isdn incoming-voice modem
isdn calling-number *****
peer default ip address pool setup-pool1
ppp authentication pap chap
ppp multilink
!
interface FastEthernet0
ip address 192.168.100.60 255.255.255.0 secondary
ip address 192.168.100.4 255.255.255.0 secondary
ip address 192.168.201.5 255.255.255.0 secondary
ip address **** 255.255.255.224
ip nat outside
duplex auto
speed auto
pppoe enable
no mop enabled
!
interface Group-Async1
ip unnumbered FastEthernet0
ip nat inside
encapsulation ppp
ip tcp header-compression
autodetect encapsulation ppp
async mode dedicated
peer default ip address pool nat
ppp authentication pap chap
group-range 1 30
!
interface Group-Async7
physical-layer async
ip unnumbered FastEthernet0
ip nat inside
encapsulation ppp
ip tcp header-compression
async mode interactive
peer default ip address pool nat
ppp authentication chap pap
!
ip local pool nat 192.168.201.200 192.168.201.240
ip local pool setup-pool1 *** ****
ip nat inside source list nat interface FastEthernet0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 ***
no ip http server
ip pim bidir-enable
!
!
ip access-list extended nat
permit ip 192.168.201.0 0.0.0.255 any
route-map cache permit 1
match ip address routewww
set ip next-hop 192.168.200.1
!
!
tacacs-server host ****
tacacs-server timeout 20
snmp-server community public RW 15
snmp-server enable traps tty
!
!
!
line con 0
password ***
logging synchronous
autocommand ppp
autoselect ppp
line 1 120
no flush-at-activation
modem Dialin
no modem status-poll
autoselect during-login
autoselect ppp
line aux 0
line vty 0 4
password fet
!
en
[/LEFT]
این بالایی مال یه بنده خدایی که من بعضی جاهاش نمیدونم چکار کرده ولی برای e1 خودم این کارو انجام میدم...توی استان فارس هم تست شده
controller e1 0
pri-group timeslots 1-30
interface serail 0:15
encapsulation ppp
isdn switch-type primary-net5
isdn incoming-voice modem 64
no cdp enable
no fair-queue
اگر اینترنت با سریال میگیری که اینم باید بزنی
interface serial0
ip unnumbered fasteh.. 0(it's up to u)
ip nat outside
encapsulation ppp
no cdp enable
no fair-queue
مرسی اهورا جان همون قسمت controller e1 کافی بود.
این دوستمون چرا برای e1 خودش no-crc4 زده؟ مگه نباید crc4 باشه؟
بعضی جاهاش خودمم نمیدونم
مثلا این قسمت ها
isdn calling-number *****
یا
modem-pool *1
pool-range 1-30
called-number **** max-conn 30
called-number rsvp-sync max-conn 30
روی serial 0:15 هم IP ست کرده !
[CODE]
controller E1 0
clock source line primary
pri-group timeslots 1-31
[/CODE]
[CODE]
interface Serial0:15
ip unnumbered Ethernet0
encapsulation ppp
isdn switch-type primary-net5
isdn incoming-voice modem
[/CODE]
مرسی. یه access 5200 داشتم با مودم patton ایوانش up نمیشد. گفتم شاید کامفیگ خاصی داره من بلد نیستم. با کمک آقا رضا فهمیدیم کابلش مشکل داره. ممنون.