AS-5300 Error in Autoselect
سلام
من یک سيسکو AS-5300 دارم که وقتي 4 - 5 تا کاربر وصل ميشن از کاربر 6 به بعد نميتونن وصل شن روی debug modem هم اين Error ها مي اد:
[LEFT]0:25:54: TTY33: Autoselect sample986-2003
Processo
00:25:54: TTY33: Autoselect sample 227D287D
00:25:54: TTY33: Autoselect sample 7D287D22
00:25:54: TTY33: Autoselect sample 287D227D
Bridging software.
00:25:54: TTY33: Autoselect sample 7D227D2D
Primary Rate ISDN sof
00:25:54: TTY33: Autoselect sample 227D2D7D
Backplane revision 2
00:25:54: TTY33: Autoselect sample 7D2D7D23
EEPROM Type 0x0001, EEP
00:25:54: TTY33: Autoselect sample 2D7D237D
00:25:54: TTY33: Autoselect sample
00:25:56: TTY33: Autoselect sample 7D23C021
00:25:56: TTY33: Autoselect sample 217D217D
00:25:56: TTY33: Autoselect sample 7D217D21
00:25:56: TTY33: Autoselect sample 217D217D
00:25:56: TTY33: Autoselect sample 7D217D20
00:25:56: TTY33: Autoselect sample 217D207D
00:25:56: TTY33: Autoselect sample 7D207D37
00:25:56: TTY33: Autoselect sample 207D377D
00:25:56: TTY33: Autoselect sample 7D377D22
00:25:56: TTY33: Autoselect sample 377D227D
00:25:56: TTY33: Autoselect sample 7D227D26
[COLOR=red][B]00:25:56: TTY33: Autoselect failed[/B][/COLOR]
00:25:56: TTY33: Line reset by "AutoSelect"
00:25:56: TTY33: Modem: (unknown)->HANGUP
00:25:56: TTY33: destroy timer type 0
00:25:56: TTY33: no timer type 1 to destroy
00:25:56: TTY33: no timer type 3 to destroy
00:25:56: TTY33: no timer type 4 to destroy
00:25:56: TTY33: no timer type 2 to destroy
00:25:57: TTY33: dropping DTR, hanging up
00:25:57: tty33: Modem: HANGUP->IDLE
00:25:57: TTY33: restoring DTR
00:25:58: TTY33: autoconfigure probe started[/LEFT]
[RIGHT]اين هم کانفيگ روترم:[/RIGHT]
[LEFT]aaa new-model
aaa authentication login default group radius line
aaa authentication ppp default if-needed group radius
aaa accounting update newinfo
aaa accounting exec default start-stop group radius
aaa accounting network default start-stop group radius
enable secret 5 $1$S9ON$ZoMCNenYi0AWVHh9GleY6/
!
spe 1/0 1/9
firmware location system:/ucode/mica_port_firmware
!
!
resource-pool disable
!
ip subnet-zero
ip rcmd rsh-enable
ip rcmd remote-host SYSTEM xxxx SYSTEM enable
ip cef
ip name-server 4.2.2.4
!
isdn switch-type primary-net5
!
controller E1 0
!
controller E1 1
framing NO-CRC4
clock source line primary
ds0-group 0 timeslots 1-15,17-31 type r2-digital
cas-custom 0
!
controller E1 2
!
controller E1 3
clock source line secondary 1
interface Ethernet0
ip address xxxx[/LEFT]
[LEFT]!
interface FastEthernet0
no ip address
duplex auto
speed auto
!
interface Group-Async0
ip unnumbered Ethernet0
encapsulation ppp
ip tcp header-compression
no ip mroute-cache
ip policy route-map e1
async mode interactive
peer default ip address pool E1
compress mppc
ppp authentication pap chap callin
ppp multilink
group-range 1 30
!
ip local pool E1 xxxx
ip classless
ip route 0.0.0.0 0.0.0.0 Ethernet0
no ip http server
!
route-map e1 permit 10
set ip next-hop xxxxx
!
snmp-server community amir RW 15
snmp-server enable traps tty
radius-server host xxxx auth-port 1645 acct-port 1646 key xxx
!
line con 0
line 1 120
no flush-at-activation
modem Dialin
modem autoconfigure type mica
transport input all
autoselect ppp
line aux 0
line vty 0 4[/LEFT]
[RIGHT]اگه ممکنه راهنماييم کنين [/RIGHT]
