-
about isdn
[RIGHT][RIGHT][FONT=Times New Roman]با سلام خدمت تمام دوستان و اساتید محترم.[/FONT][/RIGHT]
[RIGHT][FONT=Times New Roman]اول از این همه همکاری و جو واطلاعات بالای علمی و تخصصی که به وجود آوردید تشکر میکنم.[/FONT][/RIGHT]
[RIGHT][FONT=Times New Roman]من مدت 7 ماه هست که اینجا میام ولی این اولین سوال من هست.[/FONT][/RIGHT]
[FONT=Times New Roman]من دستورات و تنضیمات لازم برای تنظیم e1 روی as را تقریبا میدونم و میدونم هر دستور برای چی هست.اما چند تا سوال هست که شاید باید زودتر از اینها میپرسیدم.[/FONT]
[FONT=Times New Roman]البته قبلش بگم من خیلی از پست های اینجا رو خوندم از جمله اینها رو:[/FONT][/RIGHT]
[LEFT][RIGHT][URL="http://forum.persiannetworks.com/showthread.php?p=96569"][U][FONT=Times New Roman][COLOR=#800080]http://forum.persiannetworks.com/showthread.php?p=96569[/COLOR][/FONT][/U][/URL][/LEFT][/RIGHT]
[LEFT][RIGHT][URL="http://forum.persiannetworks.com/showthread.php?t=10331&highlight=%D8%AE%D8%B7%D9%88%D8%B7+cas+pri"][U][FONT=Times New Roman][COLOR=#800080]http://forum.persiannetworks.com/showthread.php?t=10331&highlight=%D8%AE%D8%B7%D9%88%D8%B7+cas+pri[/COLOR][/FONT][/U][/URL][/LEFT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[LEFT][RIGHT][URL="http://forum.persiannetworks.com/showthread.php?t=10367&highlight=%D8%AE%D8%B7%D9%88%D8%B7+cas+pri"][U][FONT=Times New Roman][COLOR=#800080]http://forum.persiannetworks.com/showthread.php?t=10367&highlight=%D8%AE%D8%B7%D9%88%D8%B7+cas+pri[/COLOR][/FONT][/U][/URL][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman] [/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][URL="http://forum.persiannetworks.com/showthread.php?t=7398"][U][FONT=Times New Roman][COLOR=#800080]http://forum.persiannetworks.com/showthread.php?t=7398[/COLOR][/FONT][/U][/URL][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman] [/FONT][/LEFT]
[FONT=Times New Roman]اما نتونستم جوابم رو بگیرم.[/FONT]
[FONT=Times New Roman] -1[/FONT][FONT=Times New Roman]رابطه بین interface و controller و line چیست؟؟؟[/FONT]
[FONT=Times New Roman](این رو خوندم که controller قسمتی از int هست که مسایل ارتباط فیزیکی رو فراهم میکنه.)[/FONT]
[FONT=Times New Roman] -2 [/FONT][FONT=Times New Roman]آیا طرز ارتباط اینها با هم در pri isdn و cas isdn متفاوت هست؟؟؟[/FONT]
[FONT=Times New Roman]چون در این لینک برای تنظیم pri isdn از ( x=0,1,2,3,)int serial x:15 استفاده شده [/FONT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[LEFT][RIGHT][URL="http://forum.persiannetworks.com/showthread.php?p=104492"][U][FONT=Times New Roman][COLOR=#800080]http://forum.persiannetworks.com/showthread.php?p=104492[/COLOR][/FONT][/U][/URL][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman] [/FONT][/LEFT]
[FONT=Times New Roman]در حالی که برای تنظیم cas isdn از int group-async .[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman] -3 [/FONT][FONT=Times New Roman]بعد از اینها اگر از serial برای سیگنالینگ استفاده میشه چرا از 15 تا channel استفاده شده؟؟؟[/FONT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]controller E1 3[/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]pri-group timeslots 1-31[/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]![/FONT][FONT=Times New Roman] [/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]interface Serial3:[B]15[/B][/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]ip unnumbered FastEthernet0[/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]isdn switch-type primary-net5[/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]isdn incoming-voice modem[/FONT][/LEFT][/RIGHT]
[LEFT][RIGHT][FONT=Times New Roman]isdn calling-number 9710000[/FONT][/LEFT]
[FONT=Times New Roman]طبق گفته یکی از دوستان توی این لینک( [/FONT]
[URL="http://forum.persiannetworks.com/showthread.php?t=10331&highlight=%D8%AE%D8%B7%D9%88%D8%B7+cas+pri"][U][FONT=Times New Roman][COLOR=#800080]http://forum.persiannetworks.com/showthread.php?t=10331&highlight=%D8%AE%D8%B7%D9%88%D8%B7+cas+pri[/COLOR][/FONT][/U][/URL]
[FONT=Times New Roman]) cas وpri در encapsulation هم متفاوتند) [/FONT][COLOR=black][FONT=Tahoma] تفاوتشون در نوع کپسوله کردن اطلاعات هستش ، که در [/FONT][/COLOR][B][COLOR=#ff0000][FONT=Tahoma]Cas[/FONT][/COLOR][/B][COLOR=black][FONT=Tahoma] 32 [/FONT][/COLOR][COLOR=black][FONT=Tahoma]bit[/FONT][/COLOR][COLOR=black][FONT=Tahoma] بصورت کد شده ( مثلا بصورت 0 و 1 ) و در [/FONT][/COLOR][B][COLOR=#ff0000][FONT=Tahoma]PRI[/FONT][/COLOR][/B][COLOR=black][FONT=Tahoma] به صورت فرم فرم ( مثل پکیج پکیج ) ارسال میشه[/FONT][/COLOR][FONT=Times New Roman] ( [/FONT][FONT=Times New Roman]آیا این درست است؟؟[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]بقیه سوال ها باشه برای بعد.[/FONT]
[FONT=Times New Roman]از اینکه همکاری میکنید خیلی ممنونم.[/FONT][/RIGHT]
-
[RIGHT][FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma]سلام دوست عزیز ، [/FONT]
[FONT=Tahoma]متاسفانه در ابتدا می خواهم که یک ایراد بسیار بزرگ بر شما وارد کنم . فکر می کنم که خیلی بهتر بود که در این هفت ماه شما یک جستجو اجمالی و مختصر در اینترنت انجام می دادید. قطعا پاسخ خود را حتی خیلی جامع تر از آنچه در ذهن خود دارید یافت می کردید. منابع زیادی نظیر سایت [/FONT][FONT=Tahoma]Cisco[/FONT][FONT=Tahoma] و حتی کتب مختلفی هست که مباحث این چنینی در آن شرح و توضیح داده شده است . حسب الامر چند نمونه را ذکر می کنم ، شاید در آینده مفید واقع شود.[/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma]Cisco CCNA – WAN Connection[/FONT]
[FONT=Tahoma]Cisco CCNP – ISDN Chapter[/FONT]
[FONT=Tahoma]Handbook of Broadband communications[/FONT]
[FONT=Tahoma]Articles about Digital Interfaces[/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma]من تنها به یک توضیح مختصر اکتفا می کنم و مطالعات آتی را به شما واگذار میکنم . فکر می کنم هفت ماه اینقدر مکفی بوده که کل کتاب هایی را که نام برده بودم کامل بتوان خواند. کمی تکاپو لازمه فکر می کنم . [/FONT]
[FONT=Tahoma]از نحوه نوشتن شما اینگونه برداشت می شود که شما هنوز در تعاریف مشکل دارید. و در ارتباط با نحوه کاری اطلاعات زیادی ندارید .[/FONT]
[FONT=Tahoma]1. خط [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] یک مفهموم است ، در شرح این ماهیت اینگونه بیان می شود ؛ خط [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] خطی است که ظرفیت انتقال 30 خط [/FONT][FONT=Tahoma]DS0[/FONT][FONT=Tahoma] یعنی [/FONT][FONT=Tahoma]64Kbps[/FONT][FONT=Tahoma] را داشته باشد. در اصطلاح به هریک از این [/FONT][FONT=Tahoma]DS0[/FONT][FONT=Tahoma] ها یک کانال می گویند . این کانال ها می توانند کاربری دوگانه داشته و هم برای انتقال دیتا و هم برای انتقال [/FONT][FONT=Tahoma]Voice[/FONT][FONT=Tahoma] استفاده شود. موضوع مهم در این مقوله این است که شما در زمانی که [/FONT][FONT=Tahoma]voice[/FONT][FONT=Tahoma] دارید ، نیاز دارید تا این کانال ها را تفکیک کنید . که هر کانال نشانگر یک خط تلفن است . به طوط نمنونه شما زمانی که از [/FONT][FONT=Tahoma]ISP[/FONT][FONT=Tahoma] یک خط [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] می گیرید که 30 خط برای اتصال مشترکین به صورت [/FONT][FONT=Tahoma]Dial-Up[/FONT][FONT=Tahoma] در اختیار شما قرار می دهد. [/FONT]
[FONT=Tahoma]بطور مثال [/FONT][FONT=Tahoma]NM-1CE1T1-PRI[/FONT][B][FONT=Tahoma] [/FONT][/B][FONT=Tahoma]که [/FONT][FONT=Tahoma]1-port Channelized T1/E1/ISDN-PRI network module[/FONT][FONT=Tahoma] می باشد که از این خطوط استفاده بهره وری می کند. [/FONT][FONT=Tahoma]چنین وضعیتی تحت نام [/FONT][FONT=Tahoma]Channelized E1[/FONT][FONT=Tahoma] [/FONT][FONT=Tahoma] [/FONT][FONT=Tahoma]مطرح می شود. چنین کانال ها به صورت تفکیک شده هستند. که در مبحث [/FONT][FONT=Tahoma]Cisco[/FONT][FONT=Tahoma] به اختصار [/FONT][FONT=Tahoma]CE1[/FONT][FONT=Tahoma] نوشته می شود. می توان خطوط را دو مجزا کرده و کاربری جدا و یا تنظیمات جدا برای هر یک داشت . در بعضی مواقع شما کاربری [/FONT][FONT=Tahoma]voice[/FONT][FONT=Tahoma] دارید که باز هم [/FONT][FONT=Tahoma]Channelized E1[/FONT][FONT=Tahoma] نیاز دارید . اتصال [/FONT][FONT=Tahoma]router[/FONT][FONT=Tahoma] به [/FONT][FONT=Tahoma]PABX[/FONT][FONT=Tahoma] از نمونه های بارز آن است . یا از دیگر نمنونه های ایجاد [/FONT][FONT=Tahoma]Trunk[/FONT][FONT=Tahoma] های [/FONT][FONT=Tahoma]IP/analogue/Digital[/FONT][FONT=Tahoma] می باشد. بالطبع زمانی که شما نیاز به تفکیک ندارید و کاربری دیتا مطرح می شود ، شما از دغدغه های [/FONT][FONT=Tahoma]Channelized[/FONT][FONT=Tahoma] کردن هم مبرا هستید. خوب در این حالت کاربری [/FONT][FONT=Tahoma]Data stream [/FONT][FONT=Tahoma] دارد . ماژول [/FONT][FONT=Tahoma]NM-CEM-4TE1[/FONT][FONT=Tahoma] از نمونه [/FONT][FONT=Tahoma]Module[/FONT][FONT=Tahoma] های [/FONT][FONT=Tahoma]Cisco[/FONT][FONT=Tahoma] در این زمینه است. از نمونه های کاربری انتقال 15 خط برای [/FONT][FONT=Tahoma]VOIP[/FONT][FONT=Tahoma] و 15 خط برای [/FONT][FONT=Tahoma]Data Stream[/FONT][FONT=Tahoma] می باشد .[/FONT]
[FONT=Tahoma]2. سیگنالینگ عاملی هستند که تفاوت [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] و [/FONT][FONT=Tahoma]PRI[/FONT][FONT=Tahoma] را ایجاد می کنند. نوع [/FONT][FONT=Tahoma]Signaling[/FONT][FONT=Tahoma] به کار رفته در خطوط [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] ، [/FONT][FONT=Tahoma]Q.931[/FONT][FONT=Tahoma] است. سیگانالینگ همیشه به دو صورت انجام می گیرید : [/FONT][FONT=Tahoma]Out-of-Band[/FONT][FONT=Tahoma] و [/FONT][FONT=Tahoma]in band[/FONT][FONT=Tahoma] . در [/FONT][FONT=Tahoma]in band Signaling[/FONT][FONT=Tahoma] با [/FONT][FONT=Tahoma]set[/FONT][FONT=Tahoma] کردن بیت[/FONT][FONT=Tahoma] [/FONT][FONT=Tahoma] هایی در خطوط کانال [/FONT][FONT=Tahoma] [/FONT][FONT=Tahoma]عمل سیگنالینگ انجام می گیرید . ولی در [/FONT][FONT=Tahoma]out-of-band signaling[/FONT][FONT=Tahoma] ، یک کانال مجزا وظیفه انتفال سیگنالینگ کلیه خطوط را بر عهده دارد . در اصلاح به اولی [/FONT][FONT=Tahoma]CAS[/FONT][FONT=Tahoma] و به دومی [/FONT][FONT=Tahoma]CCS[/FONT][FONT=Tahoma] گفته می شود. در [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] سنتی ، سیگنالنگ [/FONT][FONT=Tahoma]CAS[/FONT][FONT=Tahoma] است . دسته از خطوط [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] که از [/FONT][FONT=Tahoma]CCS[/FONT][FONT=Tahoma] استفاده می کنند[/FONT][FONT=Tahoma]E1 PRI[/FONT][FONT=Tahoma] خوانده می شوند. در [/FONT][FONT=Tahoma]CCS[/FONT][FONT=Tahoma] اصولا کانال 17 وظیفه سیگنالینگ تمام خطوط را بر عهده دارد. نوع [/FONT][FONT=Tahoma]Framing[/FONT][FONT=Tahoma] هر دو [/FONT][FONT=Tahoma]CRC4[/FONT][FONT=Tahoma] و [/FONT][FONT=Tahoma]Encoding[/FONT][FONT=Tahoma] مورد استفاده [/FONT][FONT=Tahoma]HDB3[/FONT][FONT=Tahoma] است. الیته این تنها عامل تفاوت این دو خط نیست .[/FONT]
[FONT=Tahoma]3. و حالا نفاوت [/FONT][FONT=Tahoma]controller[/FONT][FONT=Tahoma] و [/FONT][FONT=Tahoma]Serial Interface[/FONT][FONT=Tahoma] . هنگامی که شما ماژول[/FONT][FONT=Tahoma] [/FONT][FONT=Tahoma] [/FONT][FONT=Tahoma]E1[/FONT][FONT=Tahoma] را نصب می کنید . تنظیمات منطقی [/FONT][FONT=Tahoma]Interface[/FONT][FONT=Tahoma] همانند [/FONT][FONT=Tahoma]IP[/FONT][FONT=Tahoma]، نوع [/FONT][FONT=Tahoma]Encapsulation[/FONT][FONT=Tahoma] و غیره در این تعریف می شود. که [/FONT][FONT=Tahoma]IOS[/FONT][FONT=Tahoma] آنرا به عنوان [/FONT][FONT=Tahoma]serial Interface[/FONT][FONT=Tahoma] شناسایی می کند. هر یک از خطوط متصل شده شما دارای تنظیماتی مجزا هستند که مربوط به [/FONT][FONT=Tahoma]Physical Interface[/FONT][FONT=Tahoma] است .نوع [/FONT][FONT=Tahoma]encoding[/FONT][FONT=Tahoma] ، [/FONT][FONT=Tahoma]framing[/FONT][FONT=Tahoma] و تعداد کانال های مورد استفاده توسط [/FONT][FONT=Tahoma]controller[/FONT][FONT=Tahoma] تعریف می شوند. [/FONT]
[FONT=Tahoma] [/FONT]
[/RIGHT]
[LEFT][RIGHT][FONT=Tahoma]Controller E1 1/0[/FONT][/LEFT]
[/RIGHT]
[LEFT][RIGHT][FONT=Tahoma]Framing hdb3[/FONT][/LEFT]
[/RIGHT]
[LEFT][RIGHT][FONT=Tahoma]Linecode CRC4[/FONT][/LEFT]
[/RIGHT]
[LEFT][RIGHT][FONT=Tahoma]Pri-group timeslots 1-30 [/FONT][/LEFT]
[RIGHT][FONT=Tahoma] [/FONT][/RIGHT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT]
[FONT=Tahoma] [/FONT][/RIGHT]
-
همیشه از پستهای جناب منصوری خوشم اومده.
همینجا از اطلاعات مفید و با ارزش شما دوست عزیز که د تمامی پستهاتون به چشم میخوره تشکر میکنم.
با آرزوی موفقیت
-
[RIGHT][RIGHT][FONT=Times New Roman]آقا راست میگی .من معذرت میخواهم.اما با کمک شما راه میفتم.درست باید زحمت بیشتری بکشم .اما میخوام زودتر به نتیجه برسم. ببخشید .اما من یک سری مطالبی تهیه کردم اگه میشه یک نگاهی بیندازید:[/FONT][/RIGHT]
[FONT=Times New Roman]در رابطه با controller ,int serial, line ,int async-group در تنظیمات router و access server باید توضیح بدم که :[/FONT]
[FONT=Times New Roman] [/FONT][FONT=Times New Roman]برای اینکه سرویس isdn را بتونید به کاربران خود ارایه بدید نیاز دارید تا روی as خود تنظیماتی داشته باشید.و هر کدام از این تنظیمات مخصوص یکی از لایه های isdn است.[/FONT]
[FONT=Times New Roman]شما میدانید که یک [B]pri isdn[/B] دارای تعدادی channel هست که شماره 15در e1 و 23 در t1 برای D هست.[/FONT]
[FONT=Times New Roman]و رفتار و عملکرد B ها به وسیله تنظیمات D کنترل میشه.[/FONT]
[FONT=Times New Roman]ما ابتدا باید controller خود را تنظیم کنیم تا به وسیله اون تنظیمات سطح فیزیکی مثل framing,line code,timeslots,clock source و اینجور تنظیمات مربوط به این سطح را انجام بدیم.[/FONT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[B][FONT=Times New Roman]Configuring ISDN PRI[/FONT][/B][FONT=Times New Roman] [/FONT]
[B][FONT=Times New Roman]Step [/FONT][/B]
[B][FONT=Times New Roman]Command [/FONT][/B]
[B][FONT=Times New Roman]Purpose [/FONT][/B]
[FONT=Times New Roman][B]1[/B] [/FONT]
5300> [FONT=Times New Roman][B]enable[/B][/FONT]
Password: [FONT=Times New Roman][B]<[/B]password[B]>[/B][/FONT]
5300#
[FONT=Times New Roman]Enter enable mode.[/FONT]
[FONT=Times New Roman]Enter the password.[/FONT]
[FONT=Times New Roman]You have entered enable mode when the prompt changes to [/FONT]5300#[FONT=Times New Roman].[/FONT]
[FONT=Times New Roman][B]2[/B] [/FONT]
5300# [FONT=Times New Roman][B]config term[/B][/FONT]
Enter configuration commands, one per line. End
with CNTL/Z.
5300(config)#
[FONT=Times New Roman]Enter global configuration mode. You have entered global configuration mode when the prompt changes to [/FONT]5300(config)#.
[FONT=Times New Roman][B]3[/B] [/FONT]
5300(config)#[FONT=Times New Roman] [B]isdn switch-type[/B] [/FONT][[B][FONT=Times New Roman]primary-4ess[/FONT][/B] | [B][FONT=Times New Roman]primary-5ess[/FONT][/B] | [B][FONT=Times New Roman]primary-dms100[/FONT][/B] |
[B][FONT=Times New Roman]primary-net5[/FONT][/B] | [B][FONT=Times New Roman]primary-ntt[/FONT][/B] | [B][FONT=Times New Roman]primary-ts014[/FONT][/B]]
[FONT=Times New Roman]Enter your telco's switch type.[/FONT]
[FONT=Times New Roman][B]4[/B] [/FONT]
5300(config)# [FONT=Times New Roman][B]controller[/B] [/FONT][[B][FONT=Times New Roman]t1[/FONT][/B] | [B][FONT=Times New Roman]e1[/FONT][/B]][FONT=Times New Roman] [/FONT][[B][FONT=Times New Roman]0[/FONT][/B] | [B][FONT=Times New Roman]1[/FONT][/B] | [B][FONT=Times New Roman]2[/FONT][/B] | [B][FONT=Times New Roman]3[/FONT][/B]]
5300(config-controller)#
[FONT=Times New Roman]Enter controller configuration mode to configure your controller port. The controller ports are labeled 0 through 3 on the quad T1/PRI and quad E1/PRI cards.[/FONT]
[FONT=Times New Roman][B]5[/B] [/FONT]
5300(config-controller)#[FONT=Times New Roman] [B]framing[/B] [/FONT][[B][FONT=Times New Roman]esf[/FONT][/B] | [B][FONT=Times New Roman]sf[/FONT][/B] | [B][FONT=Times New Roman]crc4[/FONT][/B] | [B][FONT=Times New Roman]nocrc4[/FONT][/B]]
[FONT=Times New Roman]Enter your telco's framing type.[/FONT]
[FONT=Times New Roman][B]6[/B] [/FONT]
5300(config-controller)#[FONT=Times New Roman] [B]linecode[/B] [/FONT][[B][FONT=Times New Roman]ami[/FONT][/B] | [B][FONT=Times New Roman]b8zs[/FONT][/B] | [B][FONT=Times New Roman]hdb3[/FONT][/B]]
[FONT=Times New Roman]Enter your telco's line code type.[/FONT]
[FONT=Times New Roman][B]7[/B] [/FONT]
5300(config-controller)#[FONT=Times New Roman] [B]clock source line primary[/B][/FONT]
[FONT=Times New Roman]Enter the clock source for the line. Configure other lines as clock source secondary or clock source internal. Note that only one PRI can be clock source primary and only one PRI can be clock source secondary.[/FONT]
[FONT=Times New Roman][B]8[/B] [/FONT]
5300(config-controller)# [FONT=Times New Roman][B]pri-group timeslots[/B] [/FONT][[B][FONT=Times New Roman]1-24[/FONT][/B] | [B][FONT=Times New Roman]1-31[/FONT][/B]]
[FONT=Times New Roman]Configure all channels for ISDN. Enter [B]pri-group timeslots 1-24[/B] for T1. If E1, enter [B]pri-group timeslots 1-31[/B].[/FONT]
[RIGHT][FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]وقتی ما این کار را کردیم یک serial int به وجود میاید که وجود خارجی نداره اما برای تنظیم D channel لازم هست یعنی ما تنظیمات سیگنالینگ کانال D را باید در مد این سریال اینترفیس انجام بدیم. تنظیمات مختلفی بسته به شبکه ما موجود هست که بعضی هاش اینها هست:[/FONT][/RIGHT]
[B][FONT=Times New Roman]Configuring the D Channels for Modem Signaling[/FONT][/B]
[FONT=Times New Roman]Configure the ISDN D channels, which carry the control and signaling information for ISDN calls, for each ISDN PRI line.[/FONT]
[B][FONT=Times New Roman] [/FONT][FONT=Times New Roman]Configuring the D Channels for Modem Signaling[/FONT][/B][FONT=Times New Roman] [/FONT]
[B][FONT=Times New Roman]Step [/FONT][/B]
[B][FONT=Times New Roman]Command [/FONT][/B]
[B][FONT=Times New Roman]Purpose [/FONT][/B]
[FONT=Times New Roman][B]1[/B] [/FONT]
5300> [FONT=Times New Roman][B]enable[/B][/FONT]
Password: [FONT=Times New Roman][B]<[/B]password[B]>[/B][/FONT]
5300#
[FONT=Times New Roman]Enter enable mode.[/FONT]
[FONT=Times New Roman]Enter the password.[/FONT]
[FONT=Times New Roman]You have entered enable mode when the prompt changes to [/FONT]5300#[FONT=Times New Roman].[/FONT]
[FONT=Times New Roman][B]2[/B] [/FONT]
5300# [FONT=Times New Roman][B]config term[/B][/FONT]
Enter configuration commands, one per line. End
with CNTL/Z.
5300(config)#
[FONT=Times New Roman]Enter global configuration mode. You have entered global configuration mode when the prompt changes to [/FONT]5300(config)#.
[FONT=Times New Roman][B]3[/B] [/FONT]
5300(config)# [FONT=Times New Roman][B]interface serial[/B] [[B]0:15[/B] | [B]0:23[/B]][/FONT]
5300(config-if)#
[B][FONT=Times New Roman]Enter serial interface configuration mode. After you have configured the controller, a corresponding D channel serial interface is created instantly. For example, serial interface 0:23 is the D channel for controller 0. You must configure each serial interface to receive incoming and send outgoing modem signaling.[/FONT][/B]
[FONT=Times New Roman][B]4[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman][B]ip address 172.16.253.254 255.255.255.0[/B][/FONT]
[FONT=Times New Roman]Assign an IP address and subnet mask to the interface.[/FONT]
[FONT=Times New Roman][B]5[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman][B]isdn incoming-voice modem[/B][/FONT]
[FONT=Times New Roman]Configure all incoming voice calls to go to the modems.[/FONT]
[FONT=Times New Roman][B]6[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman][B]dialer-group 1[/B][/FONT]
[FONT=Times New Roman]Assign the serial interface to dialer group 1. The dialer group number is used with the [B]dialer-list[/B] command to determine which packets will be meet the criteria specified by the [B]dialer-list[/B] command and activate the ISDN connection.[/FONT]
[FONT=Times New Roman][B]7[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman][B]encapsulationppp[/B][/FONT]
[FONT=Times New Roman]Changes the default to encapsulation ppp so you can enter ppp commands.[/FONT]
[FONT=Times New Roman][B]8[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman][B]ppp multilink[/B][/FONT]
[FONT=Times New Roman]Enable PPP[/FONT][URL="http://forum.persiannetworks.com/Desktop/qq.html#3574#3574"][U][FONT=Times New Roman][COLOR=#0000ff]1[/COLOR][/FONT][/U][/URL][FONT=Times New Roman] multilink on the serial interface.[/FONT]
[FONT=Times New Roman][B]9[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman][B]ppp authentication chap pap[/B][/FONT]
[FONT=Times New Roman]Enable CHAP[/FONT][URL="http://forum.persiannetworks.com/Desktop/qq.html#3584#3584"][U][FONT=Times New Roman][COLOR=#0000ff]2[/COLOR][/FONT][/U][/URL][FONT=Times New Roman] and PAP[/FONT][URL="http://forum.persiannetworks.com/Desktop/qq.html#3587#3587"][U][FONT=Times New Roman][COLOR=#0000ff]3[/COLOR][/FONT][/U][/URL][FONT=Times New Roman] authentication on the serial interface.[/FONT]
[FONT=Times New Roman][B]10[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman]peer default ip address pool default[/FONT]
[FONT=Times New Roman]Support dial-in PC clients.[/FONT]
[FONT=Times New Roman][B]11[/B] [/FONT]
5300(config-if)# [FONT=Times New Roman][B]Ctrl-Z[/B][/FONT]
5300#
%SYS-5-CONFIG_I: Configured from console by console
[FONT=Times New Roman]Return to enable mode.[/FONT]
[FONT=Times New Roman]This message is normal and does not indicate an error[/FONT]
[RIGHT][FONT=Times New Roman] [/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]وقتی ما این تنظیمات را انجام دادیم طبق گفته cisco ما باید بتونیم توی یک test مشاهده کنید که اگر با یک تلفن شماره e1 رو گرفتید internal modem ما (به قول خودمون سوت میزنه یعنی) صدا میده.[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]اما برای اینکه بتوان از یک remote client که داره از یک مودم استفاده میکنه به as ما وصل شد و از سرویس های مختلف استفاده کرد هنوز تنظیمات دیگری لازم هست که مربوط به مودم ها هست.[/FONT]
[FONT=Times New Roman]پس تنظیمات line ,async-group مربوط به مودم های ما هست.اینکه من در بالا گفته بودم در pri از serial 0:15 استفاده میشه و در cas از async-group این رومیرسونه که من دچار اشتباه مفهومی بودم.[/FONT]
[FONT=Times New Roman]در هر دو نوع از async-group استفاده میشه چون مربوط به مودم هامون هست.[/FONT]
[FONT=Times New Roman]اینکه من گفتم اگر برای سیگنالینگ هست پس چرا 15 تا؟؟؟[/FONT]
[FONT=Times New Roman]این هم نشون میده من این دستور را نفهمیدم. 15 یک رنج را مشخص نمیکنه بلکه شماره کانال D شماست. اگر از T1 استفاده میکردیم باید جای 15 از 23 استفاده میکردیم.[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]خوب میریم سراغ تنظیمات مودم هامون.برای اینکار از دستور line [I]start[/I] [I]end [/I][I] [/I]باید استفاده کرد که به جای start و end باید رنج دلخواه از شماره مودم های اینترنال رو استفاده کنیم .یعنی ممکن هست ما بخواهیم مودم هایی را که دارید مثلا به 2 طریق تنظیم کنید مثلا یک دسته فقط dialin باشند در حالی که اون یکی inout باشه توی این مد هم دستورات مختلفی هست که دوستان خیلی هاش را توی همین سایت توضیح دادن.[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]بعد از این نوبت به async-group میرسه این تعریف را از cisco بخوانیم:[/FONT][/RIGHT]
[COLOR=black][FONT=Arial]The group-async interface is a template, which is used to control the configuration of all the async interfaces on the access server. [B]Async interfaces are lines that are running in PPP mode[/B]. An [B]async interface uses the same number as its corresponding line[/B]. Configuring the asynchronous interfaces as a group-async saves you time and configuration file size.[/FONT][/COLOR]
[RIGHT][FONT=Times New Roman]هان طور که در بالا میبینیم async group همان مودم های شما هست که در مد ppp کار میکنند. پس در این مد باید تنظیمات مربوطه را تنظیم کرد باید بدونیم که ppp روی چه لایه ای از مدلosi کار میکنه و خودش از چند لایه تشکیل شده و چه امکاناتی را در اختیار ما میگذارد.[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]این جوری ما تنظیمات مربوط بهpri isdn را انجام دادیم برای cas هم تا اونجایی که من میدونم شبیه به همین هست (البته 2 بخش آخر) و تفاوت هایی توی سیگنالینگ داره که باعث تفاوت در تنظیمات بعضی قسمت ها از جمله controller میشه که مثلا time slot ها را باید با دستور متفاوتی تنظیم کنی و ......[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]به تعریف زیر که سامان توی همین سایت تعریف کرده دقت کنیم:[/FONT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[COLOR=black][FONT=Tahoma]CAS (Channel Associated Signaling): In-band signaling, when the signaling data is sent on the same channel as the data[/FONT][/COLOR]
[RIGHT][RIGHT][FONT=Times New Roman]حالا با اجازه دوستان چند تا سوال میپرسم.امااگرجواب بدید ممنون میشم اگر هم نه سعی میکنم برم دنبالش و نتیجه را همین جا بزارم.[/FONT][/RIGHT]
[FONT=Times New Roman][B]1- [/B][B]کسی توضیحاتی در مورد [/B][B]r2-signaling [/B][B] داره؟؟[/B][B][/B][/FONT]
[FONT=Times New Roman]البته خودم این را دارم ولی دقیق تر و بیشتر میخواهم: [/FONT][/RIGHT]
[FONT=Times New Roman]R2 signaling is an international signaling standard that is common to channelized E1 networks. You can configure a channelized E1 interface to support different types of R2 signaling, which is used in older analog telephone networks.[/FONT]
[RIGHT][FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]2- [B]تفاوت دقیق [/B][B]ds0-group[/B][B] و [/B][B]cas-group[/B][B] را اگر ممکن هست دقیقا توضیح بدید(لطفا)[/B] البته من این توضیحات را دارم اما بازم شک دارم:[/FONT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[B][FONT=Univers-CondensedBold][FONT=Times New Roman]cas-group (E1 controller)[/FONT][/FONT][/B]
[FONT=Times New Roman][FONT=Times-Roman]To configure channel-associated signaling (CAS) on an E1 controller, use the [/FONT][B][FONT=Times-Bold]cas-group [/FONT][/B][FONT=Times-Roman]command in[/FONT][/FONT]
[FONT=Times New Roman][FONT=Times-Roman]controller configuration mode. To disable CAS for one or more time slots, use the [/FONT][B][FONT=Times-Bold]no [/FONT][/B][FONT=Times-Roman]form of this[/FONT][/FONT]
[FONT=Times-Roman][FONT=Times New Roman]command.[/FONT][/FONT]
[FONT=Times New Roman][B][FONT=Times-Bold]cas-group [/FONT][/B][I][FONT=Times-Italic]channel [/FONT][/I][B][FONT=Times-Bold]timeslots [/FONT][/B][I][FONT=Times-Italic]range [/FONT][/I][B][FONT=Times-Bold]type [/FONT][/B][I][FONT=Times-Italic]signal[/FONT][/I][/FONT]
[FONT=Times New Roman][B][FONT=Times-Bold]no cas-group [/FONT][/B][I][FONT=Times-Italic]channel [/FONT][/I][B][FONT=Times-Bold]timeslots [/FONT][/B][I][FONT=Times-Italic]range [/FONT][/I][B][FONT=Times-Bold]type [/FONT][/B][I][FONT=Times-Italic]signal[/FONT][/I][FONT=Univers-CondensedBold][/FONT][/FONT]
[RIGHT][FONT=Times New Roman] [/FONT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[FONT=Times New Roman][B][FONT=Univers-CondensedBold]ds0-group (controller e1)[/FONT][/B][FONT=Univers-CondensedBold][/FONT][/FONT]
[FONT=Times-Roman][FONT=Times New Roman]To define E1 channels for compressed voice calls and the channel-associated signaling (CAS) method[/FONT][/FONT]
[FONT=Times New Roman][FONT=Times-Roman]by which the router connects to the PBX or PSTN, enter the [/FONT][B][FONT=Times-Bold]ds0-group [/FONT][/B][FONT=Times-Roman]command in controller[/FONT][/FONT]
[FONT=Times New Roman][FONT=Times-Roman]configuration mode. To remove the group and signaling setting, use the [/FONT][B][FONT=Times-Bold]no [/FONT][/B][FONT=Times-Roman]form of this command.[/FONT][/FONT]
[FONT=Times New Roman][B][FONT=Times-Bold]ds0-group [/FONT][/B][I][FONT=Times-Italic]channel [/FONT][/I][B][FONT=Times-Bold]timeslots [/FONT][/B][I][FONT=Times-Italic]range [/FONT][/I][B][FONT=Times-Bold]type [/FONT][/B][I][FONT=Times-Italic]signal[/FONT][/I][/FONT]
[FONT=Times New Roman][B][FONT=Times-Bold]no ds0-group [/FONT][/B][I][FONT=Times-Italic]channel [/FONT][/I][B][FONT=Times-Bold]timeslots [/FONT][/B][I][FONT=Times-Italic]range [/FONT][/I][B][FONT=Times-Bold]type [/FONT][/B][I][FONT=Times-Italic]signal[/FONT][/I][FONT=Times-Roman][/FONT][/FONT]
[RIGHT][FONT=Times New Roman]3- در cas دیگر serial int ساخته نمیشود یعنی D channel به این صورت تنظیم نمیشود پس تنظیمتش از کجا برداشته میشود(البته من توی command reference های cisco خوندم کانال 16 اینجا هم برای سیگنالینگ استفاده میشه.البته یک خوده گیج کننده هست دوستمان گفتند کانال 17 ,برای pri ,من هم تویcisco کانال 15 , 16 را دیدم.)؟؟؟[/FONT]
[FONT=Times New Roman]4- تنظیمات قسمت cas-custom را در ایران به چه صورت باید انجام داد, آیا همان تنظیمات پیش فرض هست؟؟؟؟؟[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]این هم یک سری لینک خوب از cisco که برای من مفید بود:[/FONT]
[URL="http://www.cisco.com/en/US/products/ps6441/products_command_reference_chapter09186a00804a3bad.html"][U][FONT=Times New Roman][COLOR=#800080]http://www.cisco.com/en/US/products/ps6441/products_command_reference_chapter09186a00804a3bad.html[/COLOR][/FONT][/U][/URL]
[URL="http://www.cisco.com/en/US/products/hw/switches/ps718/products_command_reference_chapter09186a00800f025a.html"][U][FONT=Times New Roman][COLOR=#800080]http://www.cisco.com/en/US/products/hw/switches/ps718/products_command_reference_chapter09186a00800f025a.html[/COLOR][/FONT][/U][/URL]
[URL="http://www.cisco.com/en/US/products/ps6350/products_command_reference_chapter09186a0080444d0a.html"][U][FONT=Times New Roman][COLOR=#800080]http://www.cisco.com/en/US/products/ps6350/products_command_reference_chapter09186a0080444d0a.html[/COLOR][/FONT][/U][/URL]
[URL="http://www.cisco.com/en/US/products/ps6350/products_command_reference_chapter09186a0080444d97.html"][U][FONT=Times New Roman][COLOR=#800080]http://www.cisco.com/en/US/products/ps6350/products_command_reference_chapter09186a0080444d97.html[/COLOR][/FONT][/U][/URL]
[B][URL="http://www.cisco.com/en/US/products/ps6441/prod_command_reference_list.html"][U][FONT=Times New Roman][COLOR=#800080]http://www.cisco.com/en/US/products/ps6441/prod_command_reference_list.html[/COLOR][/FONT][/U][/URL][/B]
[URL="http://www.cisco.com/en/US/products/ps6441/products_command_reference_chapter09186a00804a3bad.html"][U][FONT=Times New Roman][COLOR=#800080]http://www.cisco.com/en/US/products/ps6441/products_command_reference_chapter09186a00804a3bad.html[/COLOR][/FONT][/U][/URL]
[URL="http://www.cisco.com/en/US/products/sw/iosswrel/ps1818/products_command_reference_chapter09186a008007fcdf.html"][U][FONT=Times New Roman][COLOR=#800080]http://www.cisco.com/en/US/products/sw/iosswrel/ps1818/products_command_reference_chapter09186a008007fcdf.html[/COLOR][/FONT][/U][/URL]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman]اگر دوستان کمک کنن اگر جایی من اشتباه کردم بگن تا من هم متوجه بشم و مطالب دیگری هم اضافه کنند تا من و امثال من که تازه کاریم یاد بگیریم ممنون میشم.[/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman] [/FONT]
[FONT=Times New Roman] [/FONT][/RIGHT]
[FONT=Times New Roman] [/FONT]
-
[RIGHT][RIGHT][SIZE=3][FONT=Times New Roman]سلام آقا با تشکر و عرض معذرت از تمامی دوستان .[/FONT][/SIZE][/RIGHT]
[SIZE=3][FONT=Times New Roman]من یک link خوب پیدا کردم که جواب خیلی از سوال هام را گرفتم .[/FONT][/SIZE]
[SIZE=3][FONT=Times New Roman]الان میبینم که چقدر سوال های قبلی ام خنده دار بوده .[/FONT][/SIZE]
[SIZE=3][FONT=Times New Roman]بازم از آقای منصوری تشکر میکنم[/FONT][/SIZE]
[FONT=Times New Roman][SIZE=3] [/SIZE][/FONT]
[FONT=Times New Roman][SIZE=3] [/SIZE][/FONT]
[SIZE=3][FONT=Times New Roman] این تعریف را اینجا میگذارم تا توضیحات آقای منصوری کامل شه.[/FONT][/SIZE]
[FONT=Times New Roman][SIZE=3] [/SIZE][/FONT][/RIGHT]
[FONT=Arial][SIZE=2]A channelized T1 or channelized E1 line is an analog line that was originally intended to support [/SIZE][/FONT][FONT=Arial][SIZE=2]analog voice calls, but has evolved to support analog data calls. ISDN does not transmit across channelized T1 or E1 lines. Channelized T1 and channelized E1 line are often referred to CT1 and CE1. These channelized lines are found in old world POTS networks (non ISDN).[/SIZE][/FONT]
[FONT=Arial][SIZE=2]The[/SIZE][/FONT][FONT=Arial][SIZE=2] Cisco [/SIZE][/FONT][FONT=Arial][SIZE=2]AS5200 and AS5300 Universal Access Servers supports channel-associated signaling for channelized E1 lines, which are commonly deployed in networks in Latin America, Asia, and Europe. Channel-associated signaling is configured to support channel banks in the network that convert various battery and ground operations on analog lines into signaling bits, which are forwarded over digital lines.[/SIZE][/FONT]
[FONT=Arial][SIZE=2]Channel-associated[/SIZE][/FONT][FONT=Arial][SIZE=2] signaling is call signaling that is configured on an E1 controller and enables the access server to send or receive analog calls. The signaling uses the16th channel (timeslot); thus, channel-associated signaling fits in the out-of-band signaling category.[/SIZE][/FONT]
[FONT=Arial][SIZE=2]Once[/SIZE][/FONT][FONT=Arial][SIZE=2] channel-associated signaling is configured on a single E1 controller, up to 30 remote users can simultaneously dial in to the Cisco AS5200 and Cisco AS5300 through networks running the R2 protocol. The R2 protocol is an international signaling standard for analog connections. Because R2 signaling is not supported in the Cisco AS5200 and Cisco AS5300, an E1-to-E1 converter is required[/SIZE][/FONT]