[right]با سلام
من یک خط adsl با ip static دارم به جای modem adsl می خوام از wic-adsl روی روتر 1721 استفاده کنم
اگر کسی در مورد تنظیماتش اطلاعاتی داره خواهش می کنم من راهنمائی کنه
به جای 1721 می شه از روتر 827 هم استفاده کرد .؟
متشکرم[/right]
Printable View
[right]با سلام
من یک خط adsl با ip static دارم به جای modem adsl می خوام از wic-adsl روی روتر 1721 استفاده کنم
اگر کسی در مورد تنظیماتش اطلاعاتی داره خواهش می کنم من راهنمائی کنه
به جای 1721 می شه از روتر 827 هم استفاده کرد .؟
متشکرم[/right]
[left][font=Tahoma][/font]
[/left]
[LTR][left][font=Tahoma]The configurations of a DSL connection differ depending on the router type and the way that your provider implements the connection. For example, some providers use bridging rather than a dialer method. In the example we are using, our provider has given us a PVC of 1/100. For more information on what a PVC is, see the ATM section earlier in this chapter.[/font]
[font=Tahoma]To configure the router, we enable Virtual Private Dialup Network (VPDN) and configure the virtual dialer interface, and the ATM interface itself. VPDN configures the router so that PPPoE requires "dial-in" in order to connect. Why is PPPoE configured as dial-in? Because it's the same PPP protocol that's used for authentication in dial-up connections, in this case running over Ethernet (which is the "oE" in PPPoE). The virtual dialer interface handles the IP address of the connection, the PPP authentication, and outside NAT information. Configuring the ATM interface simply entails applying the PVC value given to you by your ISP[/font]
[font=Tahoma]!
hostname ournetworkrouter
!
! Enable VPDN
vpdn enable
no vpdn logging
!
! VPDN group pppoe requires "dialin". These commands configure
! a VPDN group called "pppoe" that is used to establish the PPPoE sesions
vpdn-group pppoe
! this command means that our router is the PPPoE client
! that is requesting to establish a PPPoE session
request-dialin
protocol pppoe
!
! Create a "virtual" interface that handles the "dialing" to the
! ISP's DSL line. This virtual interface is used on the ATM0 interface
interface Dialer1
ip address negotiated
! if you have a static IP address, replace the negoatiated line above
! with the provided IP address.
encapsulation ppp
! Adjust Mtu because 1492 + PPPoE headers = 1500
ip mtu 1492
ip nat outside
dialer pool 1
ppp authentication pap callin
! Our ISP gave us the username of bob1 and password of notsecure
ppp pap sent-username bob1 password notsecure
!
interface FastEthernet0
description Our local network interface
ip address 10.10.1.1 255.255.255.0
ip nat inside
!
! Our ISP gave us a PVC of 1/100. Depending on your ISP,
! you might get a different PVC
interface ATM0
description our DSL interface
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
pvc 1/100
protocol pppoe
! Tie this interface to the virtual Dialer Interface
pppoe-client dial-pool-number 1
!
! Configure NAT to use access-list 1 as the "source" traffic
! to perform NAT on
ip nat inside source list 1 interface Dialer1 overload
!
! Our default route is the virtual dialer interface
ip route 0.0.0.0 0.0.0.0 dialer1
!
! Used in the ip nat command
access-list 1 permit 10.10.1.0 0.0.0.255
[/font]
[font=Tahoma]If your ISP says to use CHAP for authentication, replace the PPP PAP commands with these:[/font]
[font=Tahoma] ppp authentication chap callin
ppp chap hostname <username>
ppp chap password <password>
[/font]
[font=Tahoma]
[/font]
[/left]
[/LTR] [left][font=Tahoma][/font]
[/left]
[LTR][b][size=2]Configuring a Cisco 1700/2600/3600 ADSL WIC With a Single IP Address, DHCP, PPPoA, and PPP-PAP[/size][/b]
[left]
[img]http://www.cisco.com/warp/public/794/wicadsl_dhcp_1ip.gif[/img]
!
version 12.1
service timestamps debug datetime msec
service timestamps datetime msec
!
hostname R1
!
ip subnet-zero
!
ip dhcp excluded-address 10.0.0.1
[i] [color=#0000ff]!--- the DHCP pool does not lease this address; [/color][/i]
[i][color=#0000ff] !--- it is used by interface FastEthernet0[/color][/i]
!
[b]ip dhcp pool [i]poolname[/i][/b]
network 10.0.0.0 255.0.0.0
default-router 10.0.0.1
[i] [color=#0000ff]!--- default gateway is assigned to local devices[/color][/i]
!
interface FastEthernet0
ip address 10.0.0.1 255.0.0.0
no ip directed-broadcast
no ip mroute-cache
!
interface ATM0
no ip address
no ip directed-broadcast
no ip mroute-cache
no atm ilmi-keepalive
pvc 1/150
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
hold-queue 224 in
!
interface Dialer0
ip address 172.18.0.1 255.255.0.0
ip nat outside
no ip directed-broadcast
encapsulation ppp
dialer pool 1
dialer-group 2
[b]ppp pap sent-username [i]username[/i] password [i]password[/i][/b]
!
ip nat inside source list 1 interface Dialer0 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
!
access-list 1 permit 10.0.0.0 0.255.255.255
dialer-list 2 protocol ip permit
!
end[/LTR][/left]
[font=Verdana][size=2]سلام [/size][/font]
[font=Verdana][size=2]با تشکر از کاربر محترم shabake_karan (مهندس منصوری) تنظیمات کامل بود ولی چندتا سئوال برام پیش اومده اگر توضیح بدین واقعا ممنوم میشم [/size][/font]
[size=2]interface ATM0
description our DSL interface
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
!
interface ATM0.1 point-to-point
pvc 1/100
protocol pppoe
! Tie this interface to the virtual Dialer Interface
pppoe-client dial-pool-number 1[/size]
[size=2][/size]
[size=2]منظور از interface atm0.1 چیه و چه فرقی با interfce atm0 داره و چه مواقعی استفاده میشه [/size]
[size=2]نکته بعدی که اگه میشه توضیح بدین pvc چه مواقعی استفاده میشه [/size]
[size=2]با تشکر فراوان[/size]
[size=2][/size]
