نمایش نتایج: از شماره 1 تا 6 از مجموع 6

موضوع: در خواست ليست كامل دستورات و Extera seting مودم

  
  1. #1


    عضو غیر فعال شناسه تصویری Rayazma
    تاریخ عضویت
    Oct 2003
    نوشته
    87
    سپاسگزاری شده
    1
    سپاسگزاری کرده
    0

  2. #2
    نام حقيقي: محمد رسول راستی

    مدیر عمومی شناسه تصویری M-r-r
    تاریخ عضویت
    Feb 2004
    محل سکونت
    تهران
    نوشته
    9,486
    سپاسگزاری شده
    4309
    سپاسگزاری کرده
    2706

    Icon10

    بروي چشم اي عزيزم بفرما :
    Hayes Command Set / Register Formats

    +++ standard escape sequence (see S2 below)
    Comma standard pause character (see S8 below)
    AT standard attention sequence

    ATA force immediate answer
    ATC0 transmitter off
    ATC1 transmitter on

    ATD dial (ATD number)
    ATDP pulse dial (ATDP number)
    ATDT tone dial (ATDT number)

    ATE0 disable local character echo
    ATE1 enable local character echo
    ATF0 Half Duplex (modem echoes characters)
    ATF1 Full Duplex (modem does not echo characters)

    ATH0 force line on hook
    ATH1 force line off hook
    ATH2 force line special off hook (used for HAM radio)

    ATI0 request product code, formatted PPR, PP=prod., R=rev.
    ATI1 request ROM check sum

    ATL1 speaker volume low (modem specific)
    ATL2 speaker volume medium (modem specific)
    ATL3 speaker volume high (modem specific)
    ATM0 speaker always off
    ATM1 speaker on except while carrier present
    ATM2 speaker always on
    ATM3 speaker on except while dialing and carrier present

    ATO force modem into on-line state
    ATP sets modem to default pulse dial

    ATQ0 modem returns result codes
    ATQ1 modem does not return result codes

    ATR sets modem to answer mode after dialing out
    ATSn where Sn is S register number 'n' (see registers below)
    ATT sets modem to default tone dial

    ATV0 send numeric codes
    ATV1 send word result codes

    ATX0 basic result code set "CONNECT", no dial tone detect
    ATX1 extended result code set "CONNECT 1200", no dialtone detect
    ATX2 wait for dial tone, extended result codes
    ATX3 detect busy signal, extended result codes
    ATX4 wait for dial tone, detect busy, extended result codes

    ATZ reset to power up condition

    Hayes 2400 Compatible Modem Commands

    ATB0 CCITT V.22 at 1200 bps
    ATB1 BELL 212A at 1200 bps

    AT&C DCD always on
    AT&C1 DCD on while carrier present

    AT&D DTR ignored
    AT&D1 DTR fail disconnect enabled
    AT&D2 DTR fail disconnect enabled (auto answer off)
    AT&D3 DTR fail disconnect enabled (reset modem)

    AT&F restore to factory configuration

    AT&G no guard tone
    AT&G1 550 Hz guard tone
    AT&G2 1800 Hz guard tone

    AT&J RJ11/RJ41S/RJ45 jack
    AT&J2 RJ12/RJ13 jack

    AT&L regular phone line
    AT&L1 leased line

    AT&M async operation
    AT&M1 async/sync operation
    AT&M2 sync auto dial
    AT&M3 sync manual dial

    AT&P 39/61 pulse make/break ratio
    AT&P1 33/67 pulse make/break ratio

    AT&T4 grant RDL test request
    AT&T5 deny RDL test request

    AT&W write current registers to non-volatile memory

    AT&X sync clock internal

    AT&X1 sync clock external
    AT&X2 sync clock slaved

    AT&Z store dial command line

    Hayes Compatible Modem Registers

    Not all modems support all of these registers and some modems have
    registers other than those listed here. Also note, some are read only.

    to set a register use: AT Sr=## (cr)
    to read the register: AT Sr? (cr)

    Where "r" is the register and (cr) is a carriage return


    The following represent conventions used in the tables below:

    () indicates defaults for Smartmodem 1200
    ** indicates possible inconsistencies across modems


    Reg Values Register function

    S0 0-255 ring to answer on (0=don't answer)
    S1 0-255 ring count (clear after 8 sec) (read only)
    S2 0-255 escape char, normally "+", 128-255 disable escape
    S3 0-127 end of line character (0x0D/CR)
    S4 0-127 line feed character (0x0A/LF)
    S5 0-32,127 backspace character (0x08/BS)
    S6 2-255 pause before dialing in seconds (2)
    S7 1-255 wait for carrier in seconds (30)
    S8 0-255 pause for comma in dial string in seconds (2)
    S9 1-255 carrier detect response time in 1/10 second (6)
    S10 1-255 carrier loss delay in 1/10 second, 255=ignore CD (7)
    S11 50-255 touch tone dial speed, in milliseconds (70)
    S12 20-255 escape guard time, in 1/50 second,0=no delay (50)

    |7|6|5|4|3|2|1|0| S13 power up async data format
    | | | | | | | +---- unused
    | | | | | | +----- result code, 0=basic, 1=extended
    | | | | | +------ parity, 0=disabled, 1=enabled
    | | | | +------- parity, 0=odd ,1=even
    | | | +-------- data bits, 0=7 bits, 1=8 bits
    | | +--------- undefined
    | +---------- buffer ovfw flag, 0=disabled,1=enabled
    +----------- 8th bit, 0=space,1=mark (8 bit only)

    |7|6|5|4|3|2|1|0| S14 option register status data format
    | | | | | | | +---- unused **
    | | | | | | +----- local echo, 0=disabled, 1=enabled
    | | | | | +------ result codes, 0=enabled,1=disabled
    | | | | +------- result codes, 0=numeric,1=word
    | | | +-------- command recognition, 0=enable,1=disable
    | | +--------- dial method, 0=touch tone, 1=pulse
    | +---------- unused **
    +----------- 0=answer, 1=originate **

    S15 flag register **

    |7|6|5|4|3|2|1|0| S16 test status
    | | | | | | | +---- analog loop, 0=inactive, 1=active
    | | | | | | +----- unused
    | | | | | +------ digital loop, 0=inactive, 1=active
    | | | | +------- remote req digital loop,0=inact.,1=active
    | | | +-------- remote digital loop,0=inact.,1=active
    | | +--------- self test RDL, 0=inactive, 1=active
    | +---------- self test analog loop,0=inactive,1=active
    +----------- unused

    S18 0-255 remote test timer in seconds

    |7|6|5|4|3|2|1|0| S21 option status
    | | | | | | | +---- jack type, 0=RJ11,RJ41,RJ45,1=RJ12,RJ13
    | | | | | | +----- unused
    | | | | | +------ CTS state, 0=follows RTS, 1=forced on
    | | | +--------- DTR modem behavior (see below)
    | | +---------- DCD, 0=forced on, 1=follows carrier
    | +----------- DSR, 0=forced on, 1=behaves normally
    +------------ long space disconnect,0=disabled,1=enabled

    Bits
    43 DTR Modem Behavior Bits
    00 ignore DTR
    01 assume command state when DTR drops
    10 assume command state and disable auto-answer when DTR drops
    11 reset when DTR drops


    |7|6|5|4|3|2|1|0| S22 option status
    | | | | | | +------ speaker volume, 01=low,10=med,11=high
    | | | | +--------- speaker setting (see below)
    | +-------------- X command in effect
    +--------------- make/break ratio, 0=39/61, 1=33/67

    Bits
    32 S22 Speaker Setting
    00 speaker always off
    01 speaker on until carrier detected
    10 speaker always on
    11 speaker off during dialing, then on until CD

    Bits
    654 S22 X Command in Effect
    100 X1 command in effect
    101 X2 command in effect
    110 X3 command in effect
    111 X4 command in effect


    |7|6|5|4|3|2|1|0| S23 option status
    | | | | | | | +---- remote dig.loop request,0=denied,1=ok
    | | | | | +------- baud rate (see table)
    | | | | +-------- unused
    | | +----------- parity (see table)
    +-------------- guard tone setting

    Bits
    21 S23 Baud Rate Table
    00 0-300 bps
    01 600 bps
    10 1200 bps
    11 2400 bps

    Bits
    54 S23 Parity Setting
    00 even parity
    01 parity bit always 0
    10 odd parity
    11 parity bit always 1

    Bits
    76 S23 Guard Tone Setting
    00 no guard tones
    01 550 hz guard tone
    10 1800 hz guard tone

    S25 0-255 DTR detect delay in seconds (5)
    S26 0-255 RTS to CTS delay in milliseconds (1)

    |7|6|5|4|3|2|1|0| S27 option status
    | | | | | | +------ synch/async mode (see table)
    | | | | | +------- phone line, 0= public, 1=leased
    | | | | +-------- unused
    | | +----------- clock type (see table)
    | +------------ protocol, 0=CCITT V.22, 1=Bell 212A
    +------------- unused

    Bits
    10 S27 Sync/Async mode
    00 asynchronous mode
    01 async/sync mode
    10 sync auto-dial
    11 sync manual dial

    Bits
    45 S27 Clock Type
    00 internal clock used
    01 external clock used
    10 slaved clock used

    در صورتي كه از جاييش سر به در نبودي بفرما توضيح بدم خدمتتون .
    ممنونم.


    Mohammad Rasoul Rasti
    There's no place like 127.0.0.1
    m.rasti [@] outlook.com

  3. #3
    نام حقيقي: محمد رسول راستی

    مدیر عمومی شناسه تصویری M-r-r
    تاریخ عضویت
    Feb 2004
    محل سکونت
    تهران
    نوشته
    9,486
    سپاسگزاری شده
    4309
    سپاسگزاری کرده
    2706

    Icon10

    بروي چشم اي عزيزم بفرما :
    Hayes Command Set / Register Formats

    +++ standard escape sequence (see S2 below)
    Comma standard pause character (see S8 below)
    AT standard attention sequence

    ATA force immediate answer
    ATC0 transmitter off
    ATC1 transmitter on

    ATD dial (ATD number)
    ATDP pulse dial (ATDP number)
    ATDT tone dial (ATDT number)

    ATE0 disable local character echo
    ATE1 enable local character echo
    ATF0 Half Duplex (modem echoes characters)
    ATF1 Full Duplex (modem does not echo characters)

    ATH0 force line on hook
    ATH1 force line off hook
    ATH2 force line special off hook (used for HAM radio)

    ATI0 request product code, formatted PPR, PP=prod., R=rev.
    ATI1 request ROM check sum

    ATL1 speaker volume low (modem specific)
    ATL2 speaker volume medium (modem specific)
    ATL3 speaker volume high (modem specific)
    ATM0 speaker always off
    ATM1 speaker on except while carrier present
    ATM2 speaker always on
    ATM3 speaker on except while dialing and carrier present

    ATO force modem into on-line state
    ATP sets modem to default pulse dial

    ATQ0 modem returns result codes
    ATQ1 modem does not return result codes

    ATR sets modem to answer mode after dialing out
    ATSn where Sn is S register number 'n' (see registers below)
    ATT sets modem to default tone dial

    ATV0 send numeric codes
    ATV1 send word result codes

    ATX0 basic result code set "CONNECT", no dial tone detect
    ATX1 extended result code set "CONNECT 1200", no dialtone detect
    ATX2 wait for dial tone, extended result codes
    ATX3 detect busy signal, extended result codes
    ATX4 wait for dial tone, detect busy, extended result codes

    ATZ reset to power up condition

    Hayes 2400 Compatible Modem Commands

    ATB0 CCITT V.22 at 1200 bps
    ATB1 BELL 212A at 1200 bps

    AT&C DCD always on
    AT&C1 DCD on while carrier present

    AT&D DTR ignored
    AT&D1 DTR fail disconnect enabled
    AT&D2 DTR fail disconnect enabled (auto answer off)
    AT&D3 DTR fail disconnect enabled (reset modem)

    AT&F restore to factory configuration

    AT&G no guard tone
    AT&G1 550 Hz guard tone
    AT&G2 1800 Hz guard tone

    AT&J RJ11/RJ41S/RJ45 jack
    AT&J2 RJ12/RJ13 jack

    AT&L regular phone line
    AT&L1 leased line

    AT&M async operation
    AT&M1 async/sync operation
    AT&M2 sync auto dial
    AT&M3 sync manual dial

    AT&P 39/61 pulse make/break ratio
    AT&P1 33/67 pulse make/break ratio

    AT&T4 grant RDL test request
    AT&T5 deny RDL test request

    AT&W write current registers to non-volatile memory

    AT&X sync clock internal

    AT&X1 sync clock external
    AT&X2 sync clock slaved

    AT&Z store dial command line

    Hayes Compatible Modem Registers

    Not all modems support all of these registers and some modems have
    registers other than those listed here. Also note, some are read only.

    to set a register use: AT Sr=## (cr)
    to read the register: AT Sr? (cr)

    Where "r" is the register and (cr) is a carriage return


    The following represent conventions used in the tables below:

    () indicates defaults for Smartmodem 1200
    ** indicates possible inconsistencies across modems


    Reg Values Register function

    S0 0-255 ring to answer on (0=don't answer)
    S1 0-255 ring count (clear after 8 sec) (read only)
    S2 0-255 escape char, normally "+", 128-255 disable escape
    S3 0-127 end of line character (0x0D/CR)
    S4 0-127 line feed character (0x0A/LF)
    S5 0-32,127 backspace character (0x08/BS)
    S6 2-255 pause before dialing in seconds (2)
    S7 1-255 wait for carrier in seconds (30)
    S8 0-255 pause for comma in dial string in seconds (2)
    S9 1-255 carrier detect response time in 1/10 second (6)
    S10 1-255 carrier loss delay in 1/10 second, 255=ignore CD (7)
    S11 50-255 touch tone dial speed, in milliseconds (70)
    S12 20-255 escape guard time, in 1/50 second,0=no delay (50)

    |7|6|5|4|3|2|1|0| S13 power up async data format
    | | | | | | | +---- unused
    | | | | | | +----- result code, 0=basic, 1=extended
    | | | | | +------ parity, 0=disabled, 1=enabled
    | | | | +------- parity, 0=odd ,1=even
    | | | +-------- data bits, 0=7 bits, 1=8 bits
    | | +--------- undefined
    | +---------- buffer ovfw flag, 0=disabled,1=enabled
    +----------- 8th bit, 0=space,1=mark (8 bit only)

    |7|6|5|4|3|2|1|0| S14 option register status data format
    | | | | | | | +---- unused **
    | | | | | | +----- local echo, 0=disabled, 1=enabled
    | | | | | +------ result codes, 0=enabled,1=disabled
    | | | | +------- result codes, 0=numeric,1=word
    | | | +-------- command recognition, 0=enable,1=disable
    | | +--------- dial method, 0=touch tone, 1=pulse
    | +---------- unused **
    +----------- 0=answer, 1=originate **

    S15 flag register **

    |7|6|5|4|3|2|1|0| S16 test status
    | | | | | | | +---- analog loop, 0=inactive, 1=active
    | | | | | | +----- unused
    | | | | | +------ digital loop, 0=inactive, 1=active
    | | | | +------- remote req digital loop,0=inact.,1=active
    | | | +-------- remote digital loop,0=inact.,1=active
    | | +--------- self test RDL, 0=inactive, 1=active
    | +---------- self test analog loop,0=inactive,1=active
    +----------- unused

    S18 0-255 remote test timer in seconds

    |7|6|5|4|3|2|1|0| S21 option status
    | | | | | | | +---- jack type, 0=RJ11,RJ41,RJ45,1=RJ12,RJ13
    | | | | | | +----- unused
    | | | | | +------ CTS state, 0=follows RTS, 1=forced on
    | | | +--------- DTR modem behavior (see below)
    | | +---------- DCD, 0=forced on, 1=follows carrier
    | +----------- DSR, 0=forced on, 1=behaves normally
    +------------ long space disconnect,0=disabled,1=enabled

    Bits
    43 DTR Modem Behavior Bits
    00 ignore DTR
    01 assume command state when DTR drops
    10 assume command state and disable auto-answer when DTR drops
    11 reset when DTR drops


    |7|6|5|4|3|2|1|0| S22 option status
    | | | | | | +------ speaker volume, 01=low,10=med,11=high
    | | | | +--------- speaker setting (see below)
    | +-------------- X command in effect
    +--------------- make/break ratio, 0=39/61, 1=33/67

    Bits
    32 S22 Speaker Setting
    00 speaker always off
    01 speaker on until carrier detected
    10 speaker always on
    11 speaker off during dialing, then on until CD

    Bits
    654 S22 X Command in Effect
    100 X1 command in effect
    101 X2 command in effect
    110 X3 command in effect
    111 X4 command in effect


    |7|6|5|4|3|2|1|0| S23 option status
    | | | | | | | +---- remote dig.loop request,0=denied,1=ok
    | | | | | +------- baud rate (see table)
    | | | | +-------- unused
    | | +----------- parity (see table)
    +-------------- guard tone setting

    Bits
    21 S23 Baud Rate Table
    00 0-300 bps
    01 600 bps
    10 1200 bps
    11 2400 bps

    Bits
    54 S23 Parity Setting
    00 even parity
    01 parity bit always 0
    10 odd parity
    11 parity bit always 1

    Bits
    76 S23 Guard Tone Setting
    00 no guard tones
    01 550 hz guard tone
    10 1800 hz guard tone

    S25 0-255 DTR detect delay in seconds (5)
    S26 0-255 RTS to CTS delay in milliseconds (1)

    |7|6|5|4|3|2|1|0| S27 option status
    | | | | | | +------ synch/async mode (see table)
    | | | | | +------- phone line, 0= public, 1=leased
    | | | | +-------- unused
    | | +----------- clock type (see table)
    | +------------ protocol, 0=CCITT V.22, 1=Bell 212A
    +------------- unused

    Bits
    10 S27 Sync/Async mode
    00 asynchronous mode
    01 async/sync mode
    10 sync auto-dial
    11 sync manual dial

    Bits
    45 S27 Clock Type
    00 internal clock used
    01 external clock used
    10 slaved clock used


    در صورتي كه از جاييش سر به در نبودي بفرما توضيح بدم خدمتتون .



    Mohammad Rasoul Rasti
    There's no place like 127.0.0.1
    m.rasti [@] outlook.com

  4. #4
    نام حقيقي: شهاب صادقی

    عضو عادی شناسه تصویری Meteor
    تاریخ عضویت
    May 2004
    محل سکونت
    شیراز
    نوشته
    216
    سپاسگزاری شده
    141
    سپاسگزاری کرده
    15
    فقط کافیه توی گوگل دنبال چند تا کلمه خاص بگردی و اگر می خواهی مال کانکزنت را پیدا کنی همین کلمه را هم اضافه کن
    "AT Command" Modem table conexant ats0
    اون جفت گيومه ها دو طرف كلمه آ تي كامند هستند و براي اينكه مطمئن بشيم جدول را جستجو ميكنه چند تا كلمه كليدي ديگه را هم اضافه كردم .
    راستي اقاي ام آر آر ميشه بگي تنظيمات پاريتي چيه و به چه درد ميخوره ؟
    "Parity"



  5. #5
    نام حقيقي: شهاب صادقی

    عضو عادی شناسه تصویری Meteor
    تاریخ عضویت
    May 2004
    محل سکونت
    شیراز
    نوشته
    216
    سپاسگزاری شده
    141
    سپاسگزاری کرده
    15
    http://www.apache-micro.com/english/...t/v34ivcp.html
    http://www.modemhelp.net/z/zyxel.shtml
    http://www.globalvillage.com/support...T_Commands.pdf
    و كلي چيزاي ديگه كه خودت خيلي بهتر ميتوني دنبالشون بگردي



  6. #6
    نام حقيقي: omidpersia

    عضو غیر فعال شناسه تصویری omidpersia
    تاریخ عضویت
    Oct 2007
    محل سکونت
    iran
    نوشته
    4
    سپاسگزاری شده
    1
    سپاسگزاری کرده
    0
    سلام عزیزان
    یه کدی بود که با وارد کردن اون توی اکسترا خط تلفنت اشغال نمیشه اگه دارین لطف کنین



کلمات کلیدی در جستجوها:

دستورات مودمAT

کامند مودم

دستورات کامل HTML

کامند های مودم

دستورات at مودم

گوشی ccit s25

atcommand modem dialup

گوشی CCIT s5

مودم netforce

کامندهای مودم

لیست کامل دستورات html

zyxel ies 6000 configuration reset factory

گوشی های ccit

دستورات کامند مودم

گوشی هایccitگوشی های ccit z3گوشی هایccit s9CCIT s8 ‎گوشیدستورات شبکه modem ليست كامل دستورات at commandدستور pktqos در مودمدستور تریست مودملیست دستورات atcommandکامند های atگوشی ccit

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •