نمایش نتایج: از شماره 1 تا 6 از مجموع 6
سپاس ها 5سپاس
  • 1 توسط patris1
  • 2 توسط aria_irani
  • 1 توسط patris1
  • 1 توسط aria_irani

موضوع: منظور از Baseband چیست؟

  
  1. #1
    نام حقيقي: Strange

    عضو غیر فعال
    تاریخ عضویت
    Nov 2009
    محل سکونت
    Tehran
    نوشته
    21
    سپاسگزاری شده
    3
    سپاسگزاری کرده
    521

    Icon1 منظور از Baseband چیست؟

    در استاندارد های نامگذاری Ethernet از شیوه ای خاص استفاده می کنیم.
    سوالی که برایم پیش آمده این است:
    به طور مثال میگوییم 10Base-T
    منظور از 10 میزان سرعت بر حسب MBPS است
    T هم توپولوژی را تعین می کند.
    منظور از Base هم Baseband است.
    منظور از Baseband چیست؟



    موضوعات مشابه:

  2. #2
    نام حقيقي: 1234

    مدیر بازنشسته
    تاریخ عضویت
    Jul 2009
    محل سکونت
    5678
    نوشته
    5,634
    سپاسگزاری شده
    2513
    سپاسگزاری کرده
    272
    این سایت ویکی پدیا انقدر چیزه خوبیه اگر آدم یک کم توش بگرده !!

    کد:
    http://en.wikipedia.org/wiki/Ethernet
    Varieties of Ethernet

    [edit] Early varieties


    • 10BASE5: original standard uses a single coaxial cable into which you literally tap a connection by drilling into the cable to connect to the core and screen. Largely obsolete, though due to its widespread deployment in the early days, some systems may still be in use. Was known also as Thick-Ethernet.
    • 10BROAD36: Obsolete. An early standard supporting Ethernet over longer distances. It utilized broadband modulation techniques, similar to those employed in cable modem systems, and operated over coaxial cable.
    • 1BASE5: An early attempt to standardize a low-cost LAN solution, it operates at 1 Mbit/s and was a commercial failure.

    [edit] 10Mbit/s Ethernet


    • 10BASE2 (also called ThinNet or Cheapernet): 50 Ω coaxial cable connects machines together, each machine using a T-adaptor to connect to its NIC. Requires terminators at each end. For many years this was the dominant Ethernet standard 10 Mbit/s.
    • 10BASE-T: runs over four wires (two twisted pairs) on a Category 3 or Category 5 cable. A hub or switch sits in the middle and has a port for each node. This is also the configuration used for 100BASE-T and gigabit Ethernet. 10 Mbit/s.
    • FOIRL: Fiber-optic inter-repeater link. The original standard for Ethernet over fibre.
    • 10BASE-F: A generic term for the new family of 10 Mbit/s Ethernet standards: 10BASE-FL, 10BASE-FB and 10BASE-FP. Of these only 10BASE-FL is in widespread use.
      • 10BASE-FL: An updated version of the FOIRL standard.
      • 10BASE-FB: Intended for backbones connecting a number of hubs or switches, it is now obsolete.
      • 10BASE-FP: A passive star network that required no repeater, it was never implemented


    [edit] Fast Ethernet

    Main article: Fast Ethernet

    • 100BASE-T: A term for any of the three standard for 100 Mbit/s Ethernet over twisted pair cable. Includes 100BASE-TX, 100BASE-T4 and 100BASE-T2. As of 2009[update], 100BASE-TX has totally dominated the market, and is often considered to be synonymous with 100BASE-T in informal usage.
      • 100BASE-TX: 100 Mbit/s Ethernet over Category 5 cable (using two out of four pairs). Similar star-shaped configuration to 10BASE-T.
      • 100BASE-T4: 100 Mbit/s Ethernet over Category 3 cable (as used for 10BASE-T installations). Uses all four pairs in the cable, and is limited to half-duplex. Now obsolete, as Category 5 cables are the norm.
      • 100BASE-T2: 100 Mbit/s Ethernet over Category 3 cable. Uses only two pairs, and supports full-duplex. It is functionally equivalent to 100BASE-TX, but supports old cable. No products supporting this standard were ever manufactured.

    • 100BASE-FX: 100 Mbit/s Ethernet over fiber.

    [edit] Gigabit Ethernet

    Main article: Gigabit Ethernet


    [edit] 10-gigabit Ethernet

    Main article: 10 Gigabit Ethernet
    The 10 gigabit Ethernet family of standards encompasses media types for single-mode fibre (long haul), multi-mode fibre (up to 300 m), copper backplane (up to 1 m) and copper twisted pair (up to 100 m). It was first standardised as IEEE Std 802.3ae-2002, but is now included in IEEE Std 802.3-2008.

    • 10GBASE-SR: designed to support short distances over deployed multi-mode fiber cabling, it has a range of between 26 m and 82 m depending on cable type. It also supports 300 m operation over a new 2000 MHz·km multi-mode fiber.
    • 10GBASE-LX4: uses wavelength division multiplexing to support ranges of between 240 m and 300 m over deployed multi-mode cabling. Also supports 10 km over single-mode fiber.
    • 10GBASE-LR and 10GBASE-ER: these standards support 10 km and 40 km respectively over single-mode fiber.
    • 10GBASE-SW, 10GBASE-LW and 10GBASE-EW. These varieties use the WAN PHY, designed to interoperate with OC-192 / STM-64 SONET/SDH equipment. They correspond at the physical layer to 10GBASE-SR, 10GBASE-LR and 10GBASE-ER respectively, and hence use the same types of fiber and support the same distances. (There is no WAN PHY standard corresponding to 10GBASE-LX4.)
    • 10GBASE-T: designed to support copper twisted pair was specified by the IEEE Std 802.3an-2006 which has been incorporated into the IEEE Std 802.3-2008.

    As of 2009[update], 10 gigabit Ethernet is predominantly deployed in carrier networks, where 10GBASE-LR and 10GBASE-ER enjoy significant market shares.
    [edit] 40 Gigabit Ethernet and 100 Gigabit Ethernet

    Main article: 100 Gigabit Ethernet
    As of 2009[update], 40 Gigabit Ethernet and 100 Gigabit Ethernet (100GbE) standards are still in draft status.
    [edit] Related standards


    • Networking standards that are not part of the IEEE 802.3 Ethernet standard, but support the Ethernet frame format, and are capable of interoperating with it.
      • LattisNet—A SynOptics pre-standard twisted-pair 10 Mbit/s variant.
      • 100BaseVG—An early contender for 100 Mbit/s Ethernet. It runs over Category 3 cabling. Uses four pairs. Commercial failure.
      • TIA 100BASE-SX—Promoted by the Telecommunications Industry Association. 100BASE-SX is an alternative implementation of 100 Mbit/s Ethernet over fiber; it is incompatible with the official 100BASE-FX standard. Its main feature is interoperability with 10BASE-FL, supporting autonegotiation between 10 Mbit/s and 100 Mbit/s operation – a feature lacking in the official standards due to the use of differing LED wavelengths. It is targeted at the installed base of 10 Mbit/s fiber network installations.
      • TIA 1000BASE-TX—Promoted by the Telecommunications Industry Association, it was a commercial failure, and no products exist. 1000BASE-TX uses a simpler protocol than the official 1000BASE-T standard so the electronics can be cheaper, but requires Category 6 cabling.
      • G.hn—A standard developed by ITU-T and promoted by HomeGrid Forum for high-speed (up to 1 Gbit/s) local area networks over existing home wiring (coaxial cables, power lines and phone lines). G.hn defines an Application Protocol Convergence (APC) layer that accepts Ethernet frames and encapsulates them into G.hn MSDUs.






    Baseband

    کد:
    http://en.wikipedia.org/wiki/Baseband



    nikwell سپاسگزاری کرده است.

  3. #3
    نام حقيقي: آریا

    مسدود شده
    تاریخ عضویت
    Apr 2009
    محل سکونت
    تهران
    نوشته
    154
    سپاسگزاری شده
    15
    سپاسگزاری کرده
    78
    ببینید تا اونجا که من می دونم baseband داریم که برای تکنولوژی lan است و فقط برای عبور یکنوع سیگنال است مثلا در شبکه فقط سیگنالهای مربوط به lan رو می شه ارسال و دریافت کرد و voice نمیشه همزمان باهاش فرستاد. ولی در سیستم دیگری که
    broadband است و برای مخابرات استفآده می شه این امکان رو داریم که همزمان سیگنال دیتا و صدا رو باهم ارسال و دریافت کنیم مثل همین مودم a dsl هایی کهداریم و تلفنمونvoice اشغال نمیشه و اینترنت data هم کنارش داریم
    یا مثلا در شبکه های کابلی که در آمریکا هست هم سیگنال تلویزیون و هم اینترنت منتقل میشه.

    تا اونجا که من می دونم در broad band می شه چند نوع سیگنال مختلف در کنالهای مختلف رو بفرستی multiple signals in cable
    ولی در baseband تنها یک سیگنال اریال می شه


    single signal over the cable

    در ضمن اون کد آخر مثل T می تونه متغیر باشه و نشوندهنده تعریف خاصی باشه که باد از جدوال مربوط به استانداردهای اترنت پیدا کنی

    ولی کلا برای نامگذاری کابلهای از این فرمول استفاده می شه:


    Speed+Signalling Method+X
    ه از چپ به راست می شه صرعت انتقال دیتا برحسب
    Mbit/s- روش انتقال شگنال که یا Baseband یا broadband هست و متغیر X .ولی درکا چون علاقه دارید اطلاعات بیشتر رو میتونید در کتاب های network plus یا اینطوری هم مینویسن +network گیر بیارین

    اطلاعات بیشتر:
    Fast Ethernet - Wikipedia, the free encyclopedia


    برای اطلاعات بیشتر رجوع کنید به :
    Broadband - Wikipedia, the free encyclopedia


    و

    Baseband - Wikipedia, the free encyclopedia

    باز اگر در توضسحاتم اشتباهی بود بچهها تصحیح کنن.

    موفق باشید



    ویرایش توسط aria_irani : 2009-12-17 در ساعت 08:35 PM
    brellian و nikwell سپاسگزاری کرده‌اند.

  4. #4
    نام حقيقي: 1234

    مدیر بازنشسته
    تاریخ عضویت
    Jul 2009
    محل سکونت
    5678
    نوشته
    5,634
    سپاسگزاری شده
    2513
    سپاسگزاری کرده
    272
    قضیه جالبیه ، ما که نفهمیدیم چرا اعتراض شده


    nikwell سپاسگزاری کرده است.

  5. #5
    نام حقيقي: Strange

    عضو غیر فعال
    تاریخ عضویت
    Nov 2009
    محل سکونت
    Tehran
    نوشته
    21
    سپاسگزاری شده
    3
    سپاسگزاری کرده
    521
    نقل قول نوشته اصلی توسط patris1 نمایش پست ها
    این سایت ویکی پدیا انقدر چیزه خوبیه اگر آدم یک کم توش بگرده !!

    کد:
    http://en.wikipedia.org/wiki/Ethernet
    Varieties of Ethernet



    Baseband

    کد:
    http://en.wikipedia.org/wiki/Baseband

    سپاس بابت جواب
    همه جا روگشته بودم. فقط می خواستم یه جواب مثل جوابی که aria_irani عزیز دادن دریافت کنم.
    بازم ممنونم که مورد لطف قرار دادید


    نقل قول نوشته اصلی توسط aria_irani نمایش پست ها
    ببینید تا اونجا که من می دونم baseband داریم که برای تکنولوژی lan است و فقط برای عبور یکنوع سیگنال است مثلا در شبکه فقط سیگنالهای مربوط به lan رو می شه ارسال و دریافت کرد و voice نمیشه همزمان باهاش فرستاد. ولی در سیستم دیگری که
    broadband است و برای مخابرات استفآده می شه این امکان رو داریم که همزمان سیگنال دیتا و صدا رو باهم ارسال و دریافت کنیم مثل همین مودم a dsl هایی کهداریم و تلفنمونvoice اشغال نمیشه و اینترنت data هم کنارش داریم
    یا مثلا در شبکه های کابلی که در آمریکا هست هم سیگنال تلویزیون و هم اینترنت منتقل میشه.

    تا اونجا که من می دونم در broad band می شه چند نوع سیگنال مختلف در کنالهای مختلف رو بفرستی multiple signals in cable
    ولی در baseband تنها یک سیگنال اریال می شه


    single signal over the cable

    در ضمن اون کد آخر مثل T می تونه متغیر باشه و نشوندهنده تعریف خاصی باشه که باد از جدوال مربوط به استانداردهای اترنت پیدا کنی

    ولی کلا برای نامگذاری کابلهای از این فرمول استفاده می شه:


    Speed+Signalling Method+X
    ه از چپ به راست می شه صرعت انتقال دیتا برحسب
    Mbit/s- روش انتقال شگنال که یا Baseband یا broadband هست و متغیر X .ولی درکا چون علاقه دارید اطلاعات بیشتر رو میتونید در کتاب های network plus یا اینطوری هم مینویسن +network گیر بیارین

    اطلاعات بیشتر:
    Fast Ethernet - Wikipedia, the free encyclopedia


    برای اطلاعات بیشتر رجوع کنید به :
    Broadband - Wikipedia, the free encyclopedia


    و

    Baseband - Wikipedia, the free encyclopedia

    باز اگر در توضسحاتم اشتباهی بود بچهها تصحیح کنن.

    موفق باشید
    ممنون aria_irani عزیز
    همه اینا رو می دونستم عزیز.فقط این Baseband واسم سوال شده بود. توی +Network هم خونده بودم. اما یه کم گیج می زنم دیگه. چیکار کنم

    سپاس بی پایان بابت راهنمایی



  6. #6
    نام حقيقي: آریا

    مسدود شده
    تاریخ عضویت
    Apr 2009
    محل سکونت
    تهران
    نوشته
    154
    سپاسگزاری شده
    15
    سپاسگزاری کرده
    78
    نقل قول نوشته اصلی توسط nikwell نمایش پست ها
    سپاس بابت جواب
    همه جا روگشته بودم. فقط می خواستم یه جواب مثل جوابی که aria_irani عزیز دادن دریافت کنم.
    بازم ممنونم که مورد لطف قرار دادید




    ممنون aria_irani عزیز
    همه اینا رو می دونستم عزیز.فقط این Baseband واسم سوال شده بود. توی +Network هم خونده بودم. اما یه کم گیج می زنم دیگه. چیکار کنم

    سپاس بی پایان بابت راهنمایی
    خواهش میکنم دوست عزیز
    من در حد بضاعتم جواب دادم
    امیدوارم که کمکی کرده باشم
    خود من هم در این سایت از کمک و مطالب بچه ها مخصوصا سام عزیز (patris1)زیاد استفاده کردم. خوبی فوروم همینه.
    موفق باشید




    ویرایش توسط aria_irani : 2009-12-18 در ساعت 12:38 PM
    nikwell سپاسگزاری کرده است.

کلمات کلیدی در جستجوها:

base band چیست

باند پایه چیست

باند پایه چیست؟

BROAD BAND چیست

تعریف baseband

broadband چیست

Base Bandچیست

مفهوم baseband

baseband چیست

10base t چیست

10base-t چیست

10baset چیست

چیست baseband

baseband چيست؟

baseband and broadband چیستمنظور از baseband version baseband یعنی چهپهن باند چیست؟basebandچیست؟baseband و broadbandنسخه باند پایه چیستbaseband و broadband چیست؟BROADBANDچیستbroadband چیست؟baseband

برچسب برای این موضوع

مجوز های ارسال و ویرایش

  • شما نمی توانید موضوع جدید ارسال کنید
  • شما نمی توانید به پست ها پاسخ دهید
  • شما نمی توانید فایل پیوست ضمیمه کنید
  • شما نمی توانید پست های خود را ویرایش کنید
  •